what is the difference of 53 & 43 grade cement ? expailn
Answers were Sorted based on User's Feedback
Answer / kamesh
1. Fineness of cement. 53 grade fineness compare than to 43
grade cement.
2.compressive strength of concrete.
3.Low content gypsum so, 53 grade Fast Harding compare than
to 43 grade.
Is This Answer Correct ? | 74 Yes | 10 No |
Answer / deepthi ramachandran
The grade 43 and 53 in cement mainly corresponds to the
average compressive strength attained after 28 days ( 6724
hours) in mega pascals (Mpa) of at least three mortar cubes
( area of face 50 cm squared) composed of one part cement, 3
parts of standard sand( conforming to IS 650:1966) by mass
and P/4 (P is the percentage of water required to produce a
paste of standard consistency as per IS standard) + 3
percentage ( of combined mass of cement plus sand) of water
, prepared, stored and tested in the manner described in
methods of physical test for hydraulic cement.
721 hr not less than 23 MPa for 43 grade, 27 MPa for 53 grade
1682 hrs not less than 33MPa for 43 grade, 37MPa for 53 grade
6724 hrs not less than 43MPa for 43 grade, 53 MPa for 53 grade
Is This Answer Correct ? | 58 Yes | 7 No |
Answer / atul bansal
53 grade cement concrete contain more heat of hydration than
43 grade cement concrete due to more surface area for
chemical reaction so more curing and precious work required
in 53 grade of cement concrete than 43 grade cement concrete
Is This Answer Correct ? | 39 Yes | 2 No |
Answer / yamini
for 28 days strength of 43 grade is 43mpa
53 grade is 53mpa
Is This Answer Correct ? | 40 Yes | 8 No |
Answer / sridhara.n
The 53 Grade Cements Settles faster than the 43 Grade.
Is This Answer Correct ? | 30 Yes | 11 No |
Answer / subzar
Coforming to strength
attained after 28 days in Mpa.
Is This Answer Correct ? | 24 Yes | 6 No |
Answer / matu singh chauhan
43 grade-it can be used up to M30grade concrete.it is used
in precast elemant ,53 grade-it can be used more than M30,
it is used in morine structure
Is This Answer Correct ? | 28 Yes | 12 No |
Answer / vijay
1.
43 GRADE IS USED IN NORMAL STRUCTURES,
WHILE 53 GRADE IS USES IN WATER BODIES, COZ ITS SETTLEMENT IS MUCH FASTER
2.
43 GRADE HAS A COMPRESSIVE STRENGTH OF 43MPA IN 28DAYS
ND
53 HAS 53 MPA
Is This Answer Correct ? | 22 Yes | 8 No |
suppose we have a tendency to make a hole on the surface of the beam, than where we goes to make it?
difference between ordinary portland cement concrete strength and pozzolona portland cement concrete strenth
What is indicate Fe250 in steel structure?
how to calculate rate analysis of M25 grade concrete
8 Answers Nagarjuna Construction, Simplex,
How do you calculate the power of centrifugal pump?
for 200 kg of cement how is the mix proportion in kg for m25 grade of concrete
02. a. The diagonal of a 9 cube…………… 1 b. Surface area of 9 cube…………… 1 c. Volume of 1-3 cube …………… 1 d. Compressive area of 6 cube …………… 1 e. Top & Bottom face of a Cylinder/Cube is to be proper leveled to deliver the…………………………..…… properly.
10'0" × 10'0" Proposed room Start and Finish How many Cement & Sand & Bricks & Metals & Steels Need
what are the minimum compressive strength required for the concrete cube for different grades & different days .Please give me an answer.
What should be the lap length in raft if height of raft is 0.800mm ...it couldn't b 50D or 40D...we just have to join upper and bottom reinforced...is there any formula for determine it...
what should be the minimum cross sectional dimensions of column for any given loads????
For raft 3000mm thickness with T25150 mesh reinf in top and bottom what diameter can be used for chair to support mesh reinforcement