Answer / isda

IF THE VOLTAGE BETWEEN THE TWO PHASE IS EQUAL TO LAMP VOLT
IT WILL GLOW
BUT IF IT IS BIGGER IT WILL DAMAGE
IF THE VOLT LESS THE LAMP GLOWING WILL DEPEND ON THE TYPE OF
THE LAMP

Answer / arif

iamp rating is 440v the lamp will glow ,

Answer / shubham

Assuming a general situation without any rating problems(
becoz like this many problems would be there)..and lamp
means a general incandescent lamp..
for all those moments when there is a voltage difference
between the two phases the lamp will glow with output lux
proportional to the magnitude of voltage difference.i.e.
what we are going to see is a sinusoidal variation in output
lux of the bulb. i.e. from 0lux to maximum then again to
zero and so on
that's it

Answer / umar kamboh

Suppose a bulb operate at 415 volts. And there is three phase system (three phases have same voltage magnitude but 120 degree apart). The line-line voltage b/w any two phases is 415 volts (two phases have same magnitude but they will be 120 degree apart i.e 0,120 or -120).. ..The current b/w two point flow either when there is potential difference or there is phase difference (even when voltage magnitude is same).In our case (Bulb with two phases) second condition is full-filled.Hence the bulb will glow and then become dark and then glow (i.e it will blink).but remain glow for long time and will become dark for a small time (as compare to glow timing).
For further detail you may contact at
engr.umar29uet@gmail.com

Answer / am12

it will we glow koyki one phase will connected wit lemp fist solt and 2nd phase will connected with 2nd solt so we know that there will current will flow same in both phase but very small difflection in any phase that phase is working as a nutle and lemp will glow but there very loss of electricl energy

Answer / alok

If phase to phase voltage is up to the thersold voltage of Lamp it will glow, A voltage greater than thersold voltage will damage the Lamp

Answer / vinay

Moastly lamp is operat in 230v.

we are connected lamp in 2-phase so lamp across voltage is
440v so lamp is build up.& not glow

Answer / majibuddin khan

no

Answer / ankush miglani 09718151073

it will not glow it gets phase to phase n the lamp will
fuse

How does the humidity affect in breakdown voltage of air?. Is the breakdown voltage increases with the humidity?

2 Answers  

How to conduct the Magnetic Balance test on Power Transformer?

0 Answers  

what is the unit of electricity????????????

4 Answers  

What is the function of wave trap in an electrical substation?

2 Answers  

Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1.  H1-H2 = H2-H3 H3-H1 2.  H2-H3 = H3-H1 H1-H2 3.  H3-H1 = H1-H2 H2-H3 For the LV side also: 4.  X1-X0 = X2-X0 X3-X0 5.  X2-X0 = X3-X0 X1-X0 6.  X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0  H2-H0  H3-H0    X0-X1  X0-X2  X0-X3 128.0  119.9  7.2      29.2   13.3   15.8 70.7   128.4  59.2     23.4   22.0   3.6 7.2    120.1  128.1    13.4   29.3   15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?

0 Answers  

What is percent age of scrap of wires as per IE Rule Clause No in wiring for House and Industrial wiring ?

3 Answers  

400 kvtransmission lines in india are connected in star or delta

10 Answers   NTPC,

IN WHICH MODE THE TRANSFORMER WILL GET A MAXIMUM OUT PUT VOLTAGE. ASKED FOR POWER GRID EXAMINATION STAT-STAR,STAR-DELTA,DELTA-STAR,DELTA-DELTA

3 Answers  

what does the transformer connection symbol YNaod1 mean ?

3 Answers  

What is class X ct? What rare its uses?

2 Answers  

CTs Ratio

2 Answers  

What is the Difference Between the SCADA & PLC ? Both it also control and Supervise Then what Special in Scada & PLC?

1 Answers