where you provide overlap on column?

Categories >> Engineering >> Civil Engineering
Suggest New Category

Question Posted / rajlaxmigohel

10 Answers
26748 Views
ABB, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

where you provide overlap on column?..

Answer / anoop didwnaiya

h/3 above floor & h/3 below slab.
ex- if h=4mtr. then 1.33 above floor & 1.33 below slab.

Is This Answer Correct ?

37 Yes

4 No

where you provide overlap on column?..

Answer / syed urfi

Always provide lap in centre half pt of colmn.

Is This Answer Correct ?

25 Yes

4 No

where you provide overlap on column?..

Answer / girish rawat

Column laps should not be provided within confining zone.
Confining area is 500mm above floor and 500mm below beam
bottom.

Is This Answer Correct ?

23 Yes

2 No

where you provide overlap on column?..

Answer / peer mohd

coloumn top and below floor level

Is This Answer Correct ?

12 Yes

3 No

where you provide overlap on column?..

Answer / pranay

50*d for column.60*d for beam.its below the for the floor level.

Is This Answer Correct ?

4 Yes

1 No

where you provide overlap on column?..

Answer / sibi

midil half

Is This Answer Correct ?

3 Yes

1 No

where you provide overlap on column?..

Answer / nayan patel

WE MUST PROVIDE THE LAP AT THE HALF LENTH OF COLUMN. LENGHT
OF THE COLUMN IS EQUAL TO THE CLEAR DISTANCE BETWEEN TWO
ENDS

Is This Answer Correct ?

4 Yes

4 No

where you provide overlap on column?..

Answer / awadhesh kumar sharma

600MM ABOVE FLOOR LEVEL AND 600MM BELOW BEAM LEVEL THATS MEANS WHEN CLEAR LENTH OF COLUMN IS 3M THEN LAP ZONE IS 3-.6-.6=1.8

Is This Answer Correct ?

3 Yes

3 No

where you provide overlap on column?..

Answer / babu lal nayak

between end regions......

Is This Answer Correct ?

1 Yes

1 No

where you provide overlap on column?..

Answer / viplav

bottom

Is This Answer Correct ?

4 Yes

27 No

Post New Answer

More Civil Engineering Interview Questions

Consumption of Binding wire for fixing of cover block in vertical surface

0 Answers

what might be the problem faced in the near future if the M-sand is used in the place of river sand during wall plastering? (As per IS)

0 Answers

what is the quantity of formwork in shuttering and barbending is done by 1 mason and 1 helper

4 Answers CPWD,

sir, how to calculate steel per 1 m2

1 Answers

Explain the mechanism of cavitations in pipes and drains?

0 Answers

Which Types Of Bricks ?

0 Answers Assotech,

At which place Construction joint should provide in slab and Beam at the time of casting.

3 Answers

why 50% more is assumed while calculating dry volume of coarse and fine aggregates in concrete calculations.whether 50% more is correct? How is it decided? whether the same is applicable to cement volume. Also what about cement mortar dr volume? How much more is to be considered for dry volume of mortar.

1 Answers

What is the formula to calculate the volume of mortar required for a wall with 1245 blocks with a stndard size of 440x215x100?

2 Answers

please what is the number of bars required for a column of 6mx6m and 450mmx300mm,its a commercial building (Church)

0 Answers

How to calculate cement required for m20,m5 grade

8 Answers MSEB,

what is the constant weight of the 6mm,8mm,10mm,12mm,20mm,25mm etc.............dia bars in 1meter

7 Answers MPSC, NMDC,

For more Civil Engineering Interview Questions Click Here