Interested to Buy Any Domain ? << Click Here >> for more details...
what will happen if we give a dc supply to a transformer.?
- 10 Answers
- 20526 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / d.k. gupta
transformer induces e.m.f. due to rate of change of flux ,
which is only possible in a.c. supply in stationary
machines, if we will give d.c. supply as input there will
be no out put & due to core saturation after some time it
will be got damaged(burn).
| Is This Answer Correct ? | 29 Yes | 2 No |
Answer / vedpraksh uppadhaya
transformer works on mutual induction principal & we no
that an ac current change with time due to which flux
generate. if we provide dc to the transformer their is no
linkage of flux to secondary wdg. hense we will not get
anything in secondary or output
| Is This Answer Correct ? | 21 Yes | 2 No |
Answer / mayilsamy ranganathan
When Dc supply is given to primary of transformer it draws
heavy current from the DC source due to absence of back emf
and burnt out.Because the dc current not varying with time
it has constant value throught the period.
(AC is given to transformer the sinusoidaly varying
current creates a sinusoidaly varying flux ,this flux cuts
the stationary primary coils and creats a back emf,
(statically induced emf)this back emf opposes the applied
voltage source to drive current(Lenz law) so current is
limited by this back emf hence no overdrawal of current
from source,this is not happen while applying dc)
| Is This Answer Correct ? | 9 Yes | 1 No |
Answer / nithi
ANSWER:Nothing will happen.But fuse will blown off.
EXPLANATION: While applying DC voltage to the
transformer,there is no induced EMF in the primary &
secondary wdg.(except during switching period, both ON&
OFF).so,the transformer will draw high current from the
supply which detoriate the winding insulation & cause
transformer to burn.But actually this will not
happen .Becoz,the fuse will sacrifice itself to protect
transformer from high current.
| Is This Answer Correct ? | 8 Yes | 3 No |
Answer / sajid
During the time of switching flux links with primary and secondary of the Transformer voltage induced in primary and secondary after that no voltage induced in primary and secondary. Transformer primary take a large current due to the no back emf. This will damage the transformer Primary and later on secondary
Note - If any Correction please send email
msajid1980yahoo.com
| Is This Answer Correct ? | 3 Yes | 1 No |
Answer / ramineni lakshmi narayana
according to FLEMI change in flux causes EMF induced in the
conductor.
so when we give a.c change in flux happence, so EMF is
induced in the conductor.
if we give dc[constant flux],so emf induced is zero.
and winding acts as load and dissipates power in the form
of heat and due to over heat winding burns.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / sonam
for the first time when u give DC to transformer u will get some volt at the o/p for few seconds, after that no volt is transferred to secondary as because of the explanation give above
| Is This Answer Correct ? | 4 Yes | 3 No |
Answer / darababu
When DC applied to transformer ,as the dc voltage is not time varying,it produces a constant flux in primary winding,which links only with primary causes primary to burn.
| Is This Answer Correct ? | 2 Yes | 2 No |
which one is rotating transformer-single phase induction motor or 3 phase squirrel cage motor?
why resistive load has unity power factor,inductive load lagging and capacitive load leading power factor?
What should be the magnetic balance test values for a 3 phase delta/star connected single primary dual secondary winding transformer (90 MVA / 2 X 45 MVA TRANSFORMER)
How to connect the chemical earthing and complete process tell me plz
Does RCCB do the job of MCB? Lets take 16A RCCB. it trips when residual current exceeds 30mA. does it trip in an over current situation, i.e when current exceeds 16A ??
can SMPS work in DC supply ?
10 Answers HCL, IBM, Reliance,
How can step up and step down process in power transformer
1 Answers MSETCL Maharashtra State Electricity Transmission Co Ltd,
What is the permissable nutral current of three phase system as per IS standards?
what is the ambient temperature of transformer oil & winding?
415v 14kw so can u tell me how i can measure the cable size.then size of the earth also
watt meter have 4 terminals what there name??? and what theses 4 terminals indicates ?? and why 2 terminals are short circuited??
how tubelight circuit is connected and how it works?
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
