why we use negative 24vdc to a proximeter

Question Posted / princecharlesv

4 Answers
12061 Views
KNPC, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

why we use negative 24vdc to a proximeter..

Answer / munty

we use negative supply bcz the vibration sensor based on PNP
TRAANSISTOR philosophy, PNP the base voltage suppose to be
nagative.

Is This Answer Correct ?

10 Yes

1 No

why we use negative 24vdc to a proximeter..

Answer / venkatesh

In -ve voltage the rate of distabance is lesser than +ve
voltege.So we using -10vdc(some time-9.7 to -9.8vdc is
acceptable ).

Is This Answer Correct ?

11 Yes

4 No

why we use negative 24vdc to a proximeter..

Answer / manish k soni

we r not using negative supply but the 0utput
is set negative and this is ony the company
monopoly

Is This Answer Correct ?

2 Yes

7 No

why we use negative 24vdc to a proximeter..

Answer / smart dude

in vibration senseor we give -24 v in proximitor becoz it
have vaild reason
and reason is that becoz we have to take o/p of proximitor
is -10 to 0
and why we have to take the voltage o/p -10 to 0 is that
becoz and the distance b/w shaft and and sensor get less rf
signal is absobed by the meatal and voltage gets
down ,,,but acc to human mind setup as gap decrease singla
amount shoukld increase (as in case of 4 to 20 ma ),so we -
ve volatage o/p becoz as -ve voltage decrease it means vale
is increasing (acc. to math -4<-3)

Is This Answer Correct ?

5 Yes

14 No

Post New Answer

More Instrumentation Interview Questions

If a warning lamp will operate with the ground circuit is bypassed with a jumper wire to ground, what should you check?

0 Answers

my temperature transmitter in field showing 700 degree , whereas in dcs showing 459 degree, how to resolve this?

4 Answers ONGC,

I wnat to practice more online type questions .so will you show them me to take a practice test?

1 Answers VA Tech Wabag,

how to calibrate mass flow meter (Coriolis)? Example calibration range: 0 to 2500 kg/hr line size 3" fluid: Etheline glycol (MEG)

0 Answers Honeywell,

[ MITUTOYO / TESA / KUMAUN / MAHR / BRITOOL / TOHNICHY / DIATEST-GERMANY / IMADA / TECKLOK / SYLVAC /ADITYA=ACCURATE / BAKER/ CRYSTAL / FLUKE-RAYTEK ETC. 5.=SUPPLY= VERNIER CALIPERS / MICROMETERS / HEIGHTGAUGES / SLIPGAGE / BORE DIAL GAUGES / MEASURING PINS / TORQUE WRENCHES / GAUGES.. PLUGGAUGES / RINGGAUGES / SHORE A / D HARDNESS TESTERS / DIAL THICKNESS GAUGE / FEELER GAUGES / ELECTRONIC COMPARATORS WITH PROBES / DFTMETERS / SURFACE ROUGHNESS TESTERS / DIGITAL= COATING THICKNESS METERS / PROFILE PROJECTORS /.. WE ARE ALSO DEAL IN == DIGITAL TACHOMETERS / =MULTIMETERS! / VIBRATION METERS / MEGERS- INSULATION METERS / =TE! MPRATURE INDICATORS / SOUND-LEVEL METERS / ETC... =AGENCY- FLUKE- RAYTEK.. MECO....LUTRON...KYORITSU....RION

0 Answers

please someone tell me what is function of vibration sencer and how many types and how to control viberation.please. my id is jimmykhan077@gmail.com

0 Answers

please tell me how maintainence person shifted to good epc company/design company

0 Answers

how to write the program for single push button by using ladder diagram

22 Answers DigiTech,

Which standard is used for calibration of Control Valves ?

2 Answers

Can you explain drawbacks between P,I,D & PID controller

1 Answers JSW, Priya Cement, TPL,

How many interlocks at turbine? Plz explain briefly

0 Answers MRPL Mangalore Refinery and Petrochemicals Limited,

What is zero elevation and zero suppression?

0 Answers CCIE,

For more Instrumentation Interview Questions Click Here