Answer / mail2noor.hyd

when we r measuring very low pressure :: mmWC
and measuring high pr. :: kg/cm2/bar/psi... ok
for example we r measuring like boiler furnaces
pressure(draft) i.e very low pr.(250mmWC) so we r measuring
in mmWC, and when we r calibrating the transmitters (flow
and level) that time also we r calling transmitters range
also mmWC ok

here note the point is 10,000 mmWC = 1 Kg/cm2 then
1mmwc=0.0001kg/cm2 ok

Answer / vaibhav v t

10000 mmwc equals to 1 kg/cm2.
For low ranges pressure is mentioned in MMWC otherwise in
any other pressure units.

Answer / dhirendra

Mostly both are units of pressure. when we measure the very
low pressure than it is expressed in mmwc else higher
pressures are measured in kg/cm2. low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.

Answer / dilip

N/m2 is SI Unit and Kg(f)/cm2 is MKS Unit.

1 Kg/cm2 is 1.033 bar or 1.033x10^5 N/m2
10000 mmwc= 1 kg/cm2

Answer / tapan das

Mostly both are units of pressure. when we measure the very
low pressure than it is expressed in mmwc else higher
pressures are measured in kg/cm2. low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.

Answer / m.vijay kumar

both r units for pressure,.but,mmwc(millimeter water column)is
very low pressure means less than zero.here, 10000mmwc=1kg/cm2.we may consider the mmwc as vaccum.

Answer / prashant meena

Mostly both are units of pressure. when we measure the very
low pressure than it is expressed in mmwc else higher
pressures are measured in kg/cm2. low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.In thermal power plant mmwc is most useful in boiler side.

Answer / rajeev tyagii

MMWC (MILIMETR WATER COLOUM)IS A LOW PRESSURE MEASURING UNIT USE FOR LOW MEASURING AS GAS FLOW ETC AND ONE KG =10,000 MMWC.
MOSTLY USE IT INTO SAMPLE FLOW OF GASES IN ANALYSER AND FLOWMETER AND PREESURE SETTING of pressure switch also.

Answer / chirag darji

both r units of pressure itself..but when the system is in
vacuum then the pressure measured in mmwc and the positive
pressure measured by kg/cm2.so for low pressure mmwc used
and for high pressure kg/cm2 is used..

Answer / md tasleem khan

To measure low pressure we need to use this unit of
pressure Hence 10000mmwc=1kg/cm2

what would be the minimum flow rate that we can measure on rotameter..?

0 Answers   TATA,

Can any body tell me about SAP MAINTINANCE MODULE. WHAT IS its function and application. And study material Source about it. I shall be very thankful.

0 Answers  

Why ac supply load cell is used? Can we use the dc supply load cell?

0 Answers  

how to calibrate the interface leveltrol

1 Answers   Lanco,

Q- In the process of checking AC through Phase Tester our body is the part of circuit but we don't recevie Shock, Why ?

2 Answers  

Why Ma signal is using for control system?

1 Answers   Petrofac,

I HAVE PRESSURE TRANSMITTER WITH TWO WIRES 24 VOLTS SUPPLY.IF TRANSMITTER WILL GIVE SIGNAL TO THE DCS WHAT HAPPEN TO THE 24 VOLTS POWER SUPPLY IT WILL DROP OR REMAIN TO 24 VOLTS POWER SUPPLY.

3 Answers  

What is cold junction compensation in thermocouples? How is it achieved?

4 Answers   Honeywell,

How to calculate the Range of level transmitter ?

1 Answers   CPCL, Sejong, SSPL,

Why mixer nd grinder Is example of constant torque load not variable torque load ???

0 Answers  

WHAT IS THIS INSTRUMENTATION?

7 Answers  

how to tune siemens sipart electro pneumatic positioner..plz tel me..

0 Answers