Answer / joseph.a

Leakage fields present in the transformer induce eddy
currents in conductors,tanks,channels,bolts etc. and these
eddy currents give rise to stray losses.

Answer / joseph.a

Leakage fields present in the transformer induce eddy
currents in conductors,tanks,channels,bolts etc. and these
eddy currents give rise to stray losses.

Answer / engr.rasheed aftab

in case of transformer, when load is connected to the
secondary winding so flow load current. this altenating
current generate an alternating field around conductor
(winding. when this alternating field cut the conductor or
winding, an e.m.f induced in that winding.this is called
back e.m.f and current is called eddy current(Lenz's Law).
this eddy current is a cause of losses in transromer
winding. so the losses in transformer winding due to eddy
current are called stray losses. these losses also called
eddy losses. these losses are dependent on the frequency of
altenating supply because skin effect is involve in this
case. thes losses are directly propotional to the frequency.
during inrush current (harmonics) thes losses increase
because frequency increase.

Answer / vishal singh

Leakage inductance is by itself largely lossless, since energy supplied to its magnetic fields is returned to the supply with the next half-cycle. However, any leakage flux that intercepts nearby conductive materials such as the transformer's support structure will give rise to eddy currents and be converted to heat. There are also radiative losses due to the oscillating magnetic field but these are usually small.this type losses usually known as stray loss in transformer

Answer / jojo

Stray loss is caused by leakage magnetic flux that induce eddy current and hysteresis loss in nearby metallic structures. This is distinctive from core loss or sometimes called iron loss which is eddy current and hysteresis loss induced by the linkage magnetic flux in the stator iron core itself.

Answer / abhishek bansal

Stray loss is defined as Result Of eddy Currents induced in transformer due to induced Emf

Answer / nasarudheen m

stray losses is the total machine losses except total copper loss(field winding,armature wind,tr coils).so it is
hysterisisloss+windage losses+egddycurrent losses
+frictional losses.....etc

Answer / abhishek khandelwal

Leakage flux in a transformer produces eddy current in the conductors, these eddy current produces losses that is called stray loss of a transformer.

Answer / jasmine

you can see full details about losses in transformer
my advise ... this article ... http://www.top-ee.com/losses-in-transformer/
i understand all about losses in transformer

Answer / vishnu n

magenetic loss + mechanical loss

how to find impedance , mutual indatnce in transmission lines

0 Answers   NTPC,

what is the differnce between high impedance relay and low impedance relay

4 Answers   Areva,

how i calculate the syncrones generator NGR resistance .if we have a 6mw generator line voltage of generator 11kv also line current 393.3 ampere.

0 Answers  

in 132 kv substation ligtning arrestor(120 kv) connected to line. but line voltage comes to 132 kv, it operate or not???

4 Answers   Divis Laboratories,

What is grid collapse? what is the reason for it?

0 Answers  

what is sustainable current of any conductors . a bare busbar or pvc cable has different sustainable current .

0 Answers  

DOES A MAGNETIC CIRCUIT CONSUMES ENERGY? IF YES, WHY?

6 Answers  

area control error

0 Answers  

How do i perform grounding of star point of Genset (400V) for making connection with step up transformer of DELTA-DELTA (400V to 20KV) ? while Genset itself has its own neutral and grounding bus bar inside genset breaker box whereas we have another neutral and grounding busbar in synchronizing panel next to genset at maximum distance of 6meter, would someone pls advice if we can only perform neutral grounding in synchronizing panel or should we ground neutral on both places inside genset breaker box and synchronizing panel.

0 Answers   Allied Group,

why transformer ratings in kva?

99 Answers   Bhel, College School Exams Tests, DOW, Emco, Esab, GE, KCP, PGCVL, Sodexo, TCS, vtps, Wipro,

Please clarify, 1. Is it required to lay two runs of GI wire along with Armoured LT cable if it is laid between one big mains (63Amps TPN SDF) to small main (32A TPN SDF) with proper glanding termination? 2. If the armoured cable with proper glanding is laid from DB to CNC machine, is it required to run two runs of body earthing to the Machine from DB? 3.If the armoured cable with proper glanding is laid from Substation to Hangar, distance is approx. 100 mtrs, is it required to do earthing at shop area though the primary termination at substation is earthed through gland.

0 Answers   HAL,

What will happen if the oil level in the buchholz realy of a transformer gets down?

3 Answers