Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


what is the manufacturing process for impellers of closed,
semiopen and open type?



what is the manufacturing process for impellers of closed, semiopen and open type?..

Answer / abhishek

CASTING BC

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Mechanical Engineering Interview Questions

What do you treat in high alkalinity of boiler water? What is a feed water pump? What is a Booster pump?

0 Answers  


i am very much confused about direction of thrust in steam turbine...we have steam turbine of 13 stages,10 stages of impulse and 3 of reaction type....in study manual direction of thrust is towards inlet but on thrust bearing its loading side is towards condenser(exhaust side) wile also dummy ring is present in design which also restrict rotor to move in exhaust side direction not inlet ....

2 Answers  


anybody having idea about bel interview questions for mechanical,

1 Answers   BEL, Sail,


State the purpose of air heater?

1 Answers   ABC Inc, RRB, Siemens,


Preparation before arriving port?

0 Answers   RRB,


If a fixed gear having 200 teeth is in mesh with another gear having 50 teeth.The two gear are connected by an arm.What will be the number of turn made by the smaller gear for one revolution of arm about the center of bigger gear? Any effort is appreciable witha proper logic..

8 Answers  


What is the difference between Runout and Total Runoutvv

0 Answers   Valeo Lighting Systems India Private Limited,


The capacity of a domestic refrigerator is in the range of ?

0 Answers  


Hi! Greetings of the day. Can somebody tell me about as built duct sheet area calculation method. As we know that for this purpose A = (W+H)*2*L. But I have query about multiplication factors for elbows, tappers, offsets etc if there is any. Also refer the papers if available. Please revert. Thanks in advance.

0 Answers  


why the head portion of the screw jack (which carries the load when not rotating) is made hollow?

0 Answers  


How to know the bearing number if we know the shaft diameter and RPM?

1 Answers   TCH,


Explain how to measure crank web deflection?

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)