what should we do when the CT secodary gets open? how do we
short circuit it? using tester or screw driver? not
dangerous?

Answers were Sorted based on User's Feedback



what should we do when the CT secodary gets open? how do we short circuit it? using tester or scre..

Answer / gunasekaran

it may dangerous at full load condition because excessive
high voltage is build up in secondary so we have take
shutdown then only we have use tester or screw driver

Is This Answer Correct ?    11 Yes 0 No

what should we do when the CT secodary gets open? how do we short circuit it? using tester or scre..

Answer / s

if u like to change ammeter so u have to provide short link
on panel terminal....every panel having this
facility...suppose u like to use screwdriver or tester u can
use bcos there is a no voltage.....just u have to keep in yr
mind that if panel in running condition so carefully
....this type of condition occurred when u like to change
ammeter ......hope u understand

Is This Answer Correct ?    2 Yes 0 No

what should we do when the CT secodary gets open? how do we short circuit it? using tester or scre..

Answer / velu5185

no sec open plz short it because sec open CT ill burn

Is This Answer Correct ?    1 Yes 0 No

what should we do when the CT secodary gets open? how do we short circuit it? using tester or scre..

Answer / kashif saeed

it is danger to short the CT with screw driver or tester, it
is better to take the shutdown and than short the CT with
the tester or screw driver.

Is This Answer Correct ?    1 Yes 0 No

what should we do when the CT secodary gets open? how do we short circuit it? using tester or scre..

Answer / lokesh ranjith

before opening the ct or if ct get short circuit
we can short the ct terminals by using tester or can short
the terminals
causes no danger or else ct will blast

Is This Answer Correct ?    1 Yes 3 No

what should we do when the CT secodary gets open? how do we short circuit it? using tester or scre..

Answer / suresh

You should short the secondary use tester or screw driver
no prblem

Is This Answer Correct ?    2 Yes 5 No

Post New Answer

More Electrical Engineering Interview Questions

whether energy meter is connected in series or parallel.why?

2 Answers   Encom,


Why hydropower stations are preferred solution for meeting peak loads in grids?

0 Answers  


HOW TO CALCULATE UPS BATTERY BACKUP TIME

3 Answers   HSBC, VRVS,


what are the principles of a booster converter?

0 Answers  


What are the complete specifications of a motor?.

2 Answers   RRB,






is starting current of induction is high or stating current of ransformor is hign ,for the same rating

12 Answers   BARC,


what are the major difference between 3phase 3wire and 3phase 4wire trivector meter?

2 Answers   L&T, NTPC,


Dear sir, iam completed iti ncvt electrician 2000-2002 & diploma electrical eng completed 2008-2010 distance education in rvd university, still i got B licences only but my working company want C licences, how to i get c licencese pls reply me iam in critical situation thank you karthick 9841637803

0 Answers  


WHAT IS THE REASON FOR LOW VOLTAGE IN HOUSES?*

1 Answers  


What will be the minimum megger value of 1700 KVA Transformer? a) Do megger value varies according to climate conditions and area . b) If megger value is 100 mega ohm is it good for new transfomer. Explain?

4 Answers  


why back up fuse used in vacuum magnetic contactor?

1 Answers   KNPC,


what is meant by power and distribution transformer ?

0 Answers   CG,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)