Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


What happens on the secondary of a 33kV/11kV when one phase
of the primary fuse blows?

Answers were Sorted based on User's Feedback



What happens on the secondary of a 33kV/11kV when one phase of the primary fuse blows? ..

Answer / j.kesavan

one phase failure in py side ,sy side allphase got votage
with low value,

Is This Answer Correct ?    9 Yes 2 No

What happens on the secondary of a 33kV/11kV when one phase of the primary fuse blows? ..

Answer / kuttivenu

Rest of the two phases have voltage & become two phase for
the Secondary side.

Is This Answer Correct ?    5 Yes 2 No

What happens on the secondary of a 33kV/11kV when one phase of the primary fuse blows? ..

Answer / anandharaj.s

That s depands on the winding type. If windings are wound
in indivitual core 1st one is correct. If it wound in
single core then 2 nd one s correct.

Is This Answer Correct ?    0 Yes 4 No

Post New Answer



More Electrical Engineering Interview Questions

capacitor is load free component but why ampare meter shows current when capacitor bank breaker close?

5 Answers   Bhel, OPS,


How can we find the breaking capacity of a Load breaker switch (LBS) fed from 11 kv supply??ex:50KA, 26kA etc???detailed step vice answer pls.

0 Answers  


What are the safety measures of Alternator Explain them?

1 Answers   HSL,


1 unit or 1 kwh means how much kva

7 Answers   TATA,


what is differnce between grounding and earthing or both are same?

3 Answers  






132 KV TRFO BUSHING BURNT WHEN A 6.6KV HAS BEEN APPLIED TO IT .WHY .ANY REASON ?

2 Answers   MRF,


Why the rating of the HT breakers are in 1250 Amp, while the load on the breaker is around 50 Amp. ?

9 Answers   Wipro,


if 2 coil of 1000W connect in series and 200 v is applied across it . then what is the total power of coil when coil have only resistive load .

1 Answers   BSNL,


why effective resistance should be more than static resistance in transmission line?

0 Answers  


HARMONICS ARE ALWAYS IN INTEGER LIKE 2ND OR 3RD HARMONICS,NOT IN FRACTION LIKE 0.5 HARMONICS.....????????

2 Answers  


why in the three pin plug all 3 pins are cutted ?

0 Answers  


What voltage is used in Directional earth fault relay? and why?

5 Answers   L&T,






Categories
  • Civil Engineering Interview Questions Civil Engineering (5075)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4444)
  • Electrical Engineering Interview Questions Electrical Engineering (16598)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2987)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (170)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1377)