Answer / ponnu(the elite)

DOL STARTER MEANS DIRECT ON LINE STARTER WHICH IS USED 2
CONTROLS THE OVER LOADS BUT IN STAR-DELTA STARTER,FIRST WE
WILL CONNECT THE SUPPLY TO STAR.WHEN THE 80% RATED SPEED
OBTAINED,WE WILL CONNETED THE TERMINALS TO DELTA CONNECTION.

Answer / prashant

DOL STARTER IS DIRECT ON LINE STATER THIS IS ONLY FOER OVER LOAD PROTECTION BUT THE STAR DELTA STARTER IS MOTOR PROTECTION THAT IS IN START IN STAR WHEN INITIAL LOADING IS DONE THEN IN DELTA.

Answer / romil verma

When the motor is connected in Delta and started by DOL method, the voltage applied across a coil is the voltage between two phases i.e, 415V approx. Therefore the current inrush is high. In order to minimize the starting current, voltage across the coils should be brought low, which can be done if we connect the coils in star. During star connection the voltage across a coil is 240V (approx) which is 1/(sq root of 3)times that in delta which results in a simultaneous lowering of current also. This eases the stress on relays and conductors.When the motor attains 90% of its rated speed the coils are connected in Delta. therefore generating higher power.

Answer / h.l.kiran

in DOL we are going to connect 3 phase supply directly but
it will capable for less current if more current flows
through it the starter will get damage. while starting the
motor it will take more current, for reducing this start up
current we r going to star-delta connection. in this first
will be in star conection after that it will turn to delta
connection.

Answer / bheem reddy bhanu teja reddy

the voltages are reduced in dol and we can use it a proper
manner the lines are connected directly to the motor but in
star delta the voltage is step downed

Answer / bhavin makwana

the d.o.l is 0-5H.P MOTOR,AND STRE DELTA STRTER IS USE
ABOVE 5H.P MOTOR.
THE DOL IS CONNECTED TO DIRECT TO LINE.
THE STARE DELTA IS DO NOT CONNECTED TO LINE USE.
IN AUTOMATIC STARE DELTA STATER IS NO CHANGE OVER SWITCH
THEY CHANGE BY AFTER SOME TIME BY TIMER CKT.
IN STARE DELTA STRTER INITIALLY MOTOR STARTE IN STARE AFTER
SOME TIME THEY RUN IN DELTA.
SOME TEXT.....

Answer / varun machal

in case of dol starter the motor terminals directly to the power supply. & case of star delta the potential speed of motor starts in slowly

Answer / sanjeev

in dol starter starting torque is high.which is on light load.it is connectrd direct to line and used below 5hp.
in star-delta starter starting torque is 60% and it reduced to 1/3and its then connected to delta.this starter is used above 5hp.

Answer / bhavin

star delta ::This is a starting method that reduces the starting current
and starting torque. The components normally consist of three
contactors, an overload relay and a timer for setting the time in
the star-position (starting position). The motor must be delta
connected during a normal run, in order to be able to use this
starting method
dol :: this is also a starting method but some what dangerous for heavy motor who can carry heavy load. because this processes fed direct current to the motor.

Answer / dhinesh cipet

=>dol starte the motor is directly fed from the line and
=>star delta starter ther motor is started initially from
star and later during running from delta

why using carbun bresh in dc motor

3 Answers  

How RTCC panel is working and give single line diagram for RTCC with transformer?

0 Answers   AB Associates,

my 10 hp submersible pump is tripping when connected through ELCB.I have checked the megger value of the coil's with body.It was found to be 0.2mega ohm.that is leakage is there.But when connected to mccb it is not tripping.no leakage current in the motor.Is it safe to connect to mccb? what are the problem's will arise if future?also tell me in ELCB no neutral is connected to motor.than how ELCB was working?

1 Answers  

Why we are mention U1, V1, and W1 in primary side of transformer give technical reason

1 Answers  

what is mean by VCB colour code..???

1 Answers   Student,

What is making & breaking current ???

0 Answers   JLL,

role of europe union in UK safety legistlation (electrical safety)

0 Answers  

what is the distance b/w EHV lines? 1.8m 2.11m 3.4m 4.14m

7 Answers   HAL,

how we can improove power factor?????????

8 Answers   TATA,

1.What is the maximum transmission voltage in india & where it is located? 2.more information about indian power scenario.

4 Answers  

what is meant by bus bar and outgoing/incoming breaker in an electrical/electronic circuit

3 Answers  

what is the full Form of AAC ant conductor?

5 Answers