Answer / rvg

The load on the generator means,the line current draws from
the generator. Pls be remind that, generator is an energy
converting device, which converting mechanical energy to
electrical energy.
As soon as more current draws from the generator,the
mechanical load on the prime mover also rises. SO that, more
fuel consumption takes place.

Answer / haribabu dasari

Any alternator share load depend up on load angle . If we
increase fuel of prime mover , prime mover drives
alternator advance in load angle ,due to this, alternator
shares more load (load is constant so load sharing between
generators only posible).if you want to load generators
you have to switch on the load switches.

Answer / j.kesavan

fual consumption is depending upon the load.and speed of
the primovers.

Answer / nagesh

GOVERNOR IN THE FUEL PUMP DETERMINES THE LOAD OF THE ENGINE
WITH RESPECT TO SPPED OF THE ROTOR.

what is mathed of check the D.C MOTOR 181 KW (ARMATURE AND FIELD) WHAT IS THE MATHED OF CHECK THE THYRISTOR MODULE (HIGH CURRENT)

0 Answers  

---

What is the Designing & Selection Procedure for a DG/Transormer of rated capacity?

0 Answers   SCS,

---

What is mean by powerfactor. What is the difference between leading and lagging power factor?

2 Answers   HCL,

---

How induction stove works?

1 Answers  

---

1. how much normal earth resistance in earth pits(neutral and body earth) and transformer neutral and body earth & panel earth.

12 Answers   HP, Malladi Drugs and Pharmaceuticals, Pearl Engineering, PL,

---

In india the power supply is always in multiple of 11, eg.220 V, 440 V... what is the reason?

11 Answers   BSES, Electrical, L&T, PSIT,

---

why we are caling 440 volt 3 phase supply instead of 660 volt 3 phase supply? because each phase as a voltage of 220 volt. if anybody know the answer for my question please send it to my mail id. thank you.

3 Answers   College School Exams Tests, Jindal Steel and Power, JIOL, NEC,

---

1. alternator has full load regulation of 4% when pf of the load is 0.8 lag, 1500 rpm. full load regulation of 1400 rpm for 0.8lag will be ________ ?? 2. torque angle of a sync m/c operating from a constt voltage bus is usually defined as space angle between _______ . 3. method most effective in finding out no load losses in large DC shunt motoris ______ . 4. current carrying capacity of fuse material depends on ______ . 5. coil has res. 10 ohm, inductance 1H. what wil be current after 0.1sec after switching on to a 500V DC SUPPL ? ? 6. effect of phase lag compensation on servo systems ___________ . 7. rotor of a dc machine is usually supported upon ______ . 8. DC motor is preferred to AC motor in which application ?? 9. 3 nos of 10:1 Xmer are connected in Star-Delta to supply a load at 230V.the supply voltage must be ______ . 10. voltage source produces max current in which circuit. 11. cal. power, if current and voltage are out of phase by 90 degree. 12. suitable length of Xmission line of power at 66 KV. 13. Which of the theorm helps in simple computation when the load across a ckt is varying ?? 14. what is the adopted line length for power Xmission of power by cables ??

5 Answers   TATA,

---

what is XLPE cable?

2 Answers   Essar,

---

whati s the sludge current in ups

0 Answers   Future Group,

---

what law motor works?

3 Answers  

---

Can i use to 3 phase 4 wire energy meter inplace of 3 phase 3 wire energy meter ?

4 Answers  

---