Answer / satish babu

The No load current depends on the Core grade used in the
transformer laminations & the flux density at which it
operates,
a) 1-2% in high quality materials
b) 5- 10% in economy grades,

Answer / harish

dear satyendra it is no load current so wt is the use of
load????
generally no load current is 5-10% of rated value , but it
further depends on type of trformer 1 or 3 phase

Answer / dennis

No Load current will depend on Core Grade, Core Thickness,
Flux Density, Frequency and the quality of workmanship (how
good are gaps closed).

Answer / j.prabhakaran

The amount of no load current can be only calculated if we
knows the value of core loss of transformer and capacitance
current across the circuit.....

Answer / dr. alaa baiumy abdel azim &a

frist we will get the rated current of the winding
I = 630 * 1000 / CUBIC ROOT OF 3 * 11 * 1000
I = 33 Amper
I NO LOAD = 0.5% OF I RATED
NO LOAD CURRENT = O.OO5 * 33
= 165 m A

Answer / nyi lwin

transformer no load current 630 KVA....1 hour unite
question

Answer / mash

it depend on the turns of coil what is the Gage of wire...

Answer / amit sonmale

Ctually No load Curent Depend on Transfarmer eficiancy To
take load.Depend on his Copper loss.

Answer / gaurav srivastava

it is a tricky question....

u know that when transformer is at no load. the secondry
windings are open...so that there is no current flow at
secondry winding...

and for primery winding we calcute these value from OPEN
CIRCUIT TEST.

that is mentioned in all books thats have transformer
chapeter...


GAURAV SRIVASTAVA (UNITED COLLEGE OF ENGINEERING AND
RESEARCH) ALLAHABAD

Answer / nilesh

630/19.05(11*1.732)=33.07amp

Explain the operation of grid connected central solar inverter ?

0 Answers  

if single phase is having 220v supply then why three phase is having 440v instead of 660v?

4 Answers   C&S, NTPC,

Sir, I need a power supply at 380V. The supply I get in three phase is rated 415V. The total supply I have from the supply company is 70KW. Kindly inform if it is better to use a voltage stabiliser for this purpose or a transformer

3 Answers  

when the rheostat kept in minimum to maximum position in motors what will happen?

7 Answers  

We have 2 no. 4MW DG set. and GEB supply. But, we running, only 1 DG set. when we done APFC/Power factor setting : 0.90, then winding temp. Low. but when setting done : 0.83, then Winding temp. increase. WHY Why ? ? ?, plz give me answer.

4 Answers  

how the ac voltage are selected like 220v,415v,750v,1000v& 1.KV,6.6KV,11KV,33KV,66KV,132KV,220KV & why these are selected like these orders

2 Answers   Jindal, JSW,

A three phase transformer 460v primary 220v secondary (three phase four wire system.) Why did we get 460 volts across the neutral on the secondary side?

3 Answers  

why the carbon brushes are used heat created rotating parts in eiectricity

1 Answers  

1.what is the funtion of chiller primary & scondary pumps. 2.what is the use of distribution lines & Types. 3.what is the use the thermal power stations & how much capacity.

0 Answers   Wipro,

What are all the problems occured while ac generator running in leading power factor at full load condition?

1 Answers  

Sir we are using 250 kva DG its Diesel consumption 25 lits / hrs maximum load 160 kva now how to calculate units/ litres

1 Answers  

what are pilot cells

0 Answers   KSEB,