Answer / ibrahim s

This is nothing but SCADA(Supervisory Control And Data
Acquisition), this can used to monitor and control the
process variable along with PLC.

Answer / raj anu raj

As the name implies, like a supervisor who supervise his
subordinates functions and control over them.
Particularly in SCADA(supervisory control and data
aquisition)from HMI ie.. simply from monitor screen u can
supervise the various functions in the plant and also
control them by changing set points etc.. .Usualy SCADA
comprises of PLCS(functions as supervisor in auto), a
communication mode to receive data to and fro and a manual
interface ie.. for example graphics to communicate with
the PLC
Regards

Answer / khan

scada is abrreviated as supervisary control and data aqasition where the all data which monitered by the user is collected and aquared.the data can means what ever the set point acc to the program is can changed from it.
although the whole operation is monited by mmi man machine inteface first it send to the control unit then to the fild unit .

I am having a Phoenix digital to modbus converter. The o/p of the same is connected to flow computer FB407. But the digital signals are updated only after one minute in the flow computer. what may be the cause of delay in communication? Flow computer is having a scanning period of less than 1 sec.

0 Answers  

---

HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,, I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION .. ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY MANIFOLD..!!! BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 , SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT.. THANKS YOURSSSSSSS

1 Answers   Torrent Pharma,

---

hello i'am samad.Any one Can help me! How to calibrate Vaccum Transmitter DP Type range 0 - 50 mbar abs by hand pump calibrator.

4 Answers   Bharathi Cement,

---

Isometric drawings are generated during _________________ phase of a project

0 Answers  

---

What are the characteristics of Control Valve

2 Answers   Ispat,

---

---

Difference between 2-Valve Manifolds, 3-Valve Manifolds and 5-Valve Manifolds 3 with diagram

0 Answers   Acire Systems,

---

difference b/w single acting and double acting actuator by using application only?

2 Answers   McDermott,

---

What is force balance principle? State some of its’ advantages.

0 Answers  

---

what deference between panel earth and systemearth

0 Answers   Tecnimont,

---

i want know about capillary type LT transmitter installation. we can install any location in between to HP and LP leg?

2 Answers  

---

how can use ram

0 Answers  

---

For a diafhram 1.5 d =kn(p-p0) D4 Where d in deflection in inch k=constant n=no of capdule (P-P0)=Applied pressure in psi D In active dia at capsule. -1.5 d=k to p d being constant -1.5

0 Answers   L&T, Shiv Tech Marine Control,

---