I have a LT of 10000mmwc range. can i use this LT in 1000mmwc range of tank?? if

I have a LT of 10000mmwc range. can i use this LT in 1000mmwc range of tank?? if yes than what happened???

Question Posted / ravigumasana

3 Answers
7928 Views
Nirma, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

I have a LT of 10000mmwc range. can i use this LT in 1000mmwc range of tank?? if yes than what happe..

Your tx's range is 0~10000mmwc if u
use it at 0~1000mmwc head press tank
than it will indicate 10% level when tank
full. So just calibrate it (configure it) at
0~1000mmwc before take inservice for
actual reading of tank at output

Is This Answer Correct ?

17 Yes

3 No

I have a LT of 10000mmwc range. can i use this LT in 1000mmwc range of tank?? if yes than what happe..

Answer / ys

u can use this transmitter. but u should rerange the
transmitter.(ie if tank service is water and ur lt is dry
leg type,then LRV=0 and URV=1000MMH2O.. If ur lt is wet leg
calibrated, then LRV= -1000 AND URV=0 MMH2O)

Is This Answer Correct ?

2 Yes

0 No

I have a LT of 10000mmwc range. can i use this LT in 1000mmwc range of tank?? if yes than what happe..

Answer / carl_ellis

I have a LT of 10000mmwc range. can i use this LT in
1000mmwc range of tank?? if yes than what happened???

A change from a range of 10000 mmwc to 1000 mmwc is a turn
down of 10:1

If your transmitter supports a minimum range of 1000 mmwc
within the accuracy spec you require, then re-range the

transmitter and use it.

Most smart DP transmitters from major manufacturers will
support this.

Carl Ellis
Measure First

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

A pressure differential gauge type of instrument has a manifold with 2 isolation valves (hp and lp),2 vents(1 each for hp and lp) and 1 equalizing valve. Determine the position of each valve(either fully closed or fully open) when troboulshooting to: 1. zero the transmitter. 2. determine if there is a block in the impulse line. 3. determine if the gauge is functioning properly. The process fluid is water.

1 Answers

how can i communicate with non-national instruments device with pc via labVIEW8.2

3 Answers Google, Mico, National Instruments,

how to calibrate transmitter

3 Answers Sabic,

What is negative range in transmeter?

1 Answers TCL,

please can any one tell me clearly about pid tuning i am confusing about this .how to tune pid easly?

0 Answers HP, Siemens,

what is Analog input/output & Digital input/output,

2 Answers Bapco Bahrain Petroleum Company,

Can a pneumatic control valve work without positioner?

4 Answers SMC,

what is the different between plc and dcs ? I know full name of this two but I want to know what structure and working style and speed I/O capacity and controller difference?

2 Answers L&T,

What are the questions asked in fresher instrumentation candidates

0 Answers Polmon,

whyvibration probe (bently nevada ) is set -10 volt for zero reference?

2 Answers

I faced several time siemens ps2 positioner automatically getting Chang in it's set point direction after auto calibration So is there any causes biside this or any permissives ?

0 Answers

What are different types of valves?

0 Answers

For more Instrumentation Interview Questions Click Here