Answer / uthaya kumar

there is no line to line voltage

line voltage=phase to phase voltage or root 3 times of phase voltage

phase voltage= phase-neutral

for india
phase to phase voltage(line voltage) = 400v(1.732*230)
phase voltage=230v Frequency-50HZ

Answer / anil

actually question is not clear
question should be "what is phase voltage @line voltage."


Phase voltage is phase to neutral voltage.
line voltage is phase to phase voltage.

Answer / manjunatha bk

Three phases can be connected either in star (Y) or as
Delta (Δ). In star connection the line and phase currents
are one and the same. But the line to line voltage is
square root of 3 times the voltage between a line
(or phase) and the neutral.In domestic connections a
wire from the neutral and any one of the phases are
brought in.

Therefore, in Delta connection V (Phase) = V (Line) = 240
in INDIA
In Star connection V (Line) = Sqaure root 3 of V(Phase) =
415 in INDIA

Answer / venkatesh a

Phase to Phase Voltage is measured between any two phases.
Line to Line and Phase to phase is equal meaning lines. It
may be 440 Volts.

Line Voltage means Voltage is measured between the any
phase and Earth. It may be 240Volts.

Answer / hannes zorro

The phase-to-phase voltage is the voltage between the 3
phases. Line-to-line voltage is the same as phase to phase
voltage. Both are better know as the "line voltage".

The phase to neatral is the voltage between one phase and
the neatral. This is better know as the phase voltage.

Example: for a balance 3 phase 415 line voltage system, the
phase voltage is 240V (415/sq(3)). Thus, the line-to-line
is 415V and the phase to phase is 415V. The phase voltage
is 240V and the phase to neatral is 240V.

Answer / kella

--Star Circuit--

As for Phase Voltage = PVa to N
*which is always = 240V (on each phase)

As for Line Voltage = PVa to PVb
= 240 x 1.732 (square root of 3)
= 415V

*Line Voltage: The voltage present between any two of the
conductors in a three-phase system. It is 1.732 times higher
than phase voltage in a WYE connection.

*Phase Voltage: The voltage between any one conductor and
ground.

Answer / mohammed

phase to phase voltage is r to b
b to y
y to r

Answer / sandeep singh

the voltage between any phase wire and neutral is called
phase voltage and the voltage between any two phases or
lines is called line voltage

Answer / prem

phase to phase voltage=415 equal to line to line voltage.

Answer / naeem

phase to phase voltage=415 equal to line to line voltage.

why DG neutral is earth?

4 Answers   HP,

Difference B/W A/C & D/C Motors..?

10 Answers   Toyota,

In a dc series motor increases in lord current results in

4 Answers  

Two 11 kv lines are feeding to common bus in a substation,I have one set of CT & PT(3ct,2pt), How can I measure both lines power using single set.

6 Answers   L&T,

Power Factor Correction Panel (Manual & Automatic)

0 Answers  

How synchronous motor helps to improve PF? plz explain

1 Answers  

Is it required to lay 2 runs of GI wires along with armoured cables from one power DB to another Power DB?

0 Answers  

i am confused about generator. i have generator of 380 KVA that is 304 KW by that formula KW=KVA*0.8... then by this formula I=KW/V*1.732*0.8 the amperes are 528.673. so that is the load which i put on one phase of generator or this is total 3 phase load on Generator.......

3 Answers   Haliburton,

what is an oscillator?

7 Answers  

whats the differece between Exd and Exe

0 Answers   IFFCO, TN,

How do you select a cable size(Cu & Al) for a particular load?

2 Answers  

Is there any particular formula for sizing the bus bar based on the current rating

1 Answers   Bunt Solar,