if RTD damage in plant, how we know?

Categories >> Engineering >> Instrumentation
Suggest New Category

Question Posted / mistryketsn10

5 Answers
12432 Views
Reliance, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

if RTD damage in plant, how we know?..

Answer / anuj singh

First of all take a multimeter and set in resistance mode and measure if value is near 100 for pt/RTD at room temperature if value is nea zero then RTD is damage.

Is This Answer Correct ?

16 Yes

0 No

if RTD damage in plant, how we know?..

Answer / anuj singh

measure resistance by multimeter of RTD if it is near zero then your RTD damaged.

Is This Answer Correct ?

7 Yes

2 No

if RTD damage in plant, how we know?..

Answer / md gulfraj alam

sorry sir my english is touch week .. first take a multimeter and set in resistance mode and measure the rtd.if 100 ohm resistance at 0Â° centigrade then rtd pt-100 is ok near value 99-101 ohm resistance.and same case in pt50,pt25,pt500,pt100 etc only value is isolated of all rtd.otherwise rtd is damage when not match the value..i hope u understanding my ans.thank you

Is This Answer Correct ?

3 Yes

0 No

if RTD damage in plant, how we know?..

Answer / nvr

it can be known by two different way. first by measuring
resistance by using multimeter and second way to use
measure temp by using temp simulator.

Is This Answer Correct ?

2 Yes

0 No

if RTD damage in plant, how we know?..

Answer / rahul singh

PT 100 means, 100 ohm at 0 degree. and 4 ohm increasing
with every 10 degree temp.
eg: if resistance show 120 ohm that means temp should be
show about 50 degree.

Is This Answer Correct ?

1 Yes

1 No

Post New Answer

More Instrumentation Interview Questions

What is an SCR?

4 Answers GAIL,

What is the difference b/w EMF, voltage & potential difference?

1 Answers

How can SmartPlant Instrumentation users take advantage of these global services?

1 Answers

explain level transmitter working

1 Answers

Sir, I want junior executive, Instrumentation question papaer for IOCL, Plz send to arabinda.ghosh83@gmail.com

0 Answers IOCL,

[ MITUTOYO / TESA / KUMAUN / MAHR / BRITOOL / TOHNICHY / DIATEST-GERMANY / IMADA / TECKLOK / SYLVAC /ADITYA=ACCURATE / BAKER/ CRYSTAL / FLUKE-RAYTEK ETC. 5.=SUPPLY= VERNIER CALIPERS / MICROMETERS / HEIGHTGAUGES / SLIPGAGE / BORE DIAL GAUGES / MEASURING PINS / TORQUE WRENCHES / GAUGES.. PLUGGAUGES / RINGGAUGES / SHORE A / D HARDNESS TESTERS / DIAL THICKNESS GAUGE / FEELER GAUGES / ELECTRONIC COMPARATORS WITH PROBES / DFTMETERS / SURFACE ROUGHNESS TESTERS / DIGITAL= COATING THICKNESS METERS / PROFILE PROJECTORS /.. WE ARE ALSO DEAL IN == DIGITAL TACHOMETERS / =MULTIMETERS! / VIBRATION METERS / MEGERS- INSULATION METERS / =TE! MPRATURE INDICATORS / SOUND-LEVEL METERS / ETC... =AGENCY- FLUKE- RAYTEK.. MECO....LUTRON...KYORITSU....RION

0 Answers

why k factor is important to know in flow transmitter. if we don,t know k factor what will be issue we can face .

1 Answers Flour Tech Engineers (P) Ltd,

If we increase PI controller what will be action.

1 Answers IMECO,

How find CGPA? when marks are 515/850 & 2559/3350. Plz any one tell me.

1 Answers

how can we calibrate RADAR LEVEL transmitter 0% to 100%

3 Answers Chevron Phillips, Honeywell,

what is the difference between auto tuning and manual tuning of controllers(eg:PID,PI,PD CONTROLLERS )

2 Answers GATE,

If you calibrate a pneumatic pressure transmitter, how many adjustments are normally necessary or mandatory?

1 Answers

For more Instrumentation Interview Questions Click Here