.What are the equipments should run when there is a black
out in power plant.

Answers were Sorted based on User's Feedback



.What are the equipments should run when there is a black out in power plant...

Answer / sengar kunal

For Turbine, DC Emergency Oil Pump should run to lubricate turbine and generator bearings till turbine fully coasts down safely and after coasting down STG Turning gear should be switched on.

Is This Answer Correct ?    10 Yes 0 No

.What are the equipments should run when there is a black out in power plant...

Answer / bibhu

Emergency oil pump(EOP) must be run for lubrication and the
the bearing gear motor(BGM for moving the turbine shaft).

Is This Answer Correct ?    3 Yes 0 No

.What are the equipments should run when there is a black out in power plant...

Answer / azam

The lubrication pumps for turbine, start motor and the control supply for i/o and MV feeders should always be available for specially gas turbines.

Is This Answer Correct ?    3 Yes 0 No

.What are the equipments should run when there is a black out in power plant...

Answer / arun

LUBE OIL SYSTEM ( Dc Pump in Service )

SEAL OIL SYSTEM ( TO Prevent Escape of Hydrogen in Generetor )

Is This Answer Correct ?    3 Yes 0 No

.What are the equipments should run when there is a black out in power plant...

Answer / anbu

DG set and DC Emergency oil pump should run to lubricate turbine and generator bearings. If DC Emergency oil pump got problem means lubrication oil will supply by overhead oil tank.

Is This Answer Correct ?    3 Yes 0 No

Post New Answer

More Power Plant Engineering Interview Questions

why do we use contro fluid tank (cft)in turbo generator area(tg) in power plant?

1 Answers   MPL,


Why the steam Turbines are Designed Higher side compare to Alternator

1 Answers  


what is the perfect location for furnace draft transmitter in AFBC boiler?

1 Answers  


why seal air fan is used and where it is used and where is suction taken from

7 Answers   Bhel, ETO,


how shall you calculate PLF on the basis of percentage auxillary load factor

6 Answers  






Is it not bad to bleed steam from turbine stages before utilizing its energy.

2 Answers  


procedure of how to generate power in solar plant.

0 Answers  


.What is drip and drain.

2 Answers   NPTI,


How to calculate air to fuel ratio in boilers

1 Answers  


im try to calculating seawater flow required for SW-FGD system. I need a guide, equation or method to do it, can some one help me! Thanks very much

0 Answers   Student,


In a thermal power plant ID Fans running with full load but boiler load is only 80 % give reason ?

9 Answers   Essar, Prumatech, Tata Power,


what equipment is most efficient in power plant?

4 Answers   Adani,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)