whyvibration probe (bently nevada ) is set -10 volt for
zero reference?

Answers were Sorted based on User's Feedback



whyvibration probe (bently nevada ) is set -10 volt for zero reference?..

Answer / p.n.shaji

Hello

See some comments

http://www.control.com/thread/1026233734

Regards

Is This Answer Correct ?    3 Yes 0 No

whyvibration probe (bently nevada ) is set -10 volt for zero reference?..

Answer / faiyaz

Bentley neveda system generally used in -10 volt and -9 volt because its measure a gap voltage Bentley neveda system work in the principle of NPN transistor its measure a negative voltage that is why

Is This Answer Correct ?    3 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

how to caluculate flow by using transmitter?tell me plz I am eagerly waiting for your reply..

2 Answers   Agi Glaspac, Reliance Power,


Regarding MOS (maintenance override switch), I want to know its function and its state ( 1 or 0 when not activated ). An example will be very helpful..thank you.

1 Answers  


typical loop drawing of a simple feedback control comprising of one transmitter and one control

1 Answers  


What are the different types of temperature sensors and the principle they work on?

1 Answers   GAIL,


A pressure transmitter with a range of 0-100 bar.The accuracy of the instrument is 1% of upper range value? The pressure indicating transmitter is showing the system pressure is 50 bar. b. When you include the error, what is the minimum possible pressure in our fuel gas system? i. 49.5 bar ii. 49 bar iii. 1 bar iv. 0.5 bar We want to change the filter cartridge. We must depressure the fuel gas system. c. After we depressure the system in preparation for maintenance, the transmitter displays a pressure of +0.1 bar. At this time, what is the possible range of pressures in our fuel system? i. +0.099 to +0.101 bar ii. 0 to +0.2 bar iii. -0.1 to +0.3 bar iv. -0.9 to +1.1 bar

3 Answers  


what does mean by analog output trim and where this one used for?

1 Answers  


Are Coils of Electromagnetic flowmeter in direct contact with fluid material

4 Answers   TATA,


what will be the output of a temperature transmitter if temperature is 120 degree celcius?

6 Answers   KNPC,


I need to know steps to Calibration Valve Guard......

1 Answers  


Can anybody tell me the exact explanation for Functional calibration?When it should be done on process or on lab? Advanced Thanks

2 Answers  


which instrument is most commonly used to observe the external features of a grasshopper's abdomen?

1 Answers  


What is cv of control valve

4 Answers   Cadila,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)