we have taken HV test of 2.5 k and Megger test on 11 kv HT cable.here it show

we have taken HV test of 2.5 k and Megger test on 11 kv HT
cable.here it shows no fault but when we are charging the
same cable with 11 kv supply why the VCB 11 kv gets tripped
can anybody define the possible cause of fault ?

Question Posted / bhimesh pardhi

4 Answers
5464 Views
MAHINDRA, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

we have taken HV test of 2.5 k and Megger test on 11 kv HT cable.here it shows no fault but when ..

Answer / shariff

The 11kV cable will be designed for morethan 12kV and the
megger applied voltage is just 20% of that rating.. so the
cable insulation might be withstanding at that vg but it is
failing at higher voltage.. So go for the Hi pot test with
DC pulse nearly 15kV...

Is This Answer Correct ?

4 Yes

1 No

we have taken HV test of 2.5 k and Megger test on 11 kv HT cable.here it shows no fault but when ..

Answer / shariff

Is This Answer Correct ?

1 Yes

1 No

we have taken HV test of 2.5 k and Megger test on 11 kv HT cable.here it shows no fault but when ..

Answer / nagesh.patwari

Check out the control circuit. And every possible relevant thing in panel cable breaker.... Thoroughly.

Is This Answer Correct ?

0 Yes

0 No

we have taken HV test of 2.5 k and Megger test on 11 kv HT cable.here it shows no fault but when ..

Answer / shariff

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

what is diffence between synchronus and asynchronus AC motor.?

1 Answers

can we run a motor rated 50Hz,415vac,1440RPM At higher speed then rated on name plate with the help of VFD /drive on long term basis.wheater it will effect the motor life

3 Answers

why fault current time duration is calculated for 1 minutes?

1 Answers Rockfort Engineering,

what type of motor is used in fan

6 Answers

Can any one help me how to set an overload set the range from 2.8A to 4A , rated motor current 22A, CT 60/5A

2 Answers

Can we use MCCB with Auxiliary Contact in place of Contactor in a AMF System.

1 Answers C&S, Farnek,

WHAT IS SITTING AMPS IN OVER-LOAD RELAY FOR 1PH OR 3PH MOTORS?IF ITS NAME PLATE GIVEN MAX AMPS 10AMPS?

1 Answers

What types domain of laplace transforms? What behavior can laplace transform predict how the system work?

0 Answers

sometimes, eventhough the HV side of the transformer is opened there is a voltage in LV side .How is it possible?

4 Answers

How does a tertiary winding filter harmonic(espcially 3rd one) from entering into load system?

0 Answers

What will happen to transformer if we gave 5HZ input instead of 50/60Hz??? explain with reason

2 Answers

bit confused - am i correct in thinking that to determine line to line voltage in a star config 110v 3 phase 4 wire distribution system i would use a voltmeter? I have a circuit configured as an unbalanced load, consisting of three incandescent lamps (1x40w, 1x60w, 1x100w - all 110v rated)connected in a star configuration to a 110v 3 phase 4 wire distribution system. I want to find out what types of meters i would use to obtain: a) each line to line voltage b) the line to neutral voltage across each load c) current flowing in each line and load d) current flowing in the neutral conductor e) power supplied to the loads im assuming i would be using ammeters in series along each line and voltmeters in parallel across each line to neutral? Also how could i predict these meter readings before taking them and with which formulae? Any help would be greatly appreciated A.

1 Answers

For more Electrical Engineering Interview Questions Click Here