Answer / ravi kumar

TNC switch is nothing but two position switch. when it is
in close position it will put the circuit breaker in
operation by energising the closing coil and when it is in
trip position it will trip the circuit by energise the trip
coil in circuit breaker.

Answer / minimanu

IT is a three position Switch. The swith atre of two types -
Having lockable Trip position and other with spring return
to normal Neutral position.
For manual operation this switch is used to TRIP a breaker
by moving it towards trip position and close by moving it
towards Close position.

In neutral position all the operations on AUTO mode or from
remote can be done, as per the scheme.

For keeping the breaker in OFF condition or for isolation,
the switch can be kept in lockable TRIP position, if that
facility is available in the switch.

Answer / vikas s adhatrao

TNC switch is a three position switch, used for closing or
tripping a circuit breaker manually from panel (locally).
this switch is spring loaded, this ensures that switch
returns to neutral position after any operation (either
close or trip). This is required to isloate the closing /
trip coils, which are short time rated, from the control
supply.TNC switch makes close open commands momentary.

Answer / pks

trip neutral close is the switch of breaker thro' which we
can keep the breaker energised thro' closed coil, we can
keep the breaker in off condition thro' trip coil or
breaker can be used in operation mode auto by keeping on
neutral..

by using TNC switch manually we can energise the CC or TC
of breaker.

Answer / varma

TNC is a 3 position switch used for closing or tripping a
circuit breaker manually from panel locally. TNC siwtch
returns to Neutral position after any operation.

Answer / akhilesh solanki

TNC Switch is normally used for the breakers. This is not simple Control switch with spring loaded. The special features of the TNC Switches are as below.
1. Close can be done only after tripping the breaker. This is required to ensure that successive operation of closing coil can not be done.Required for safety of closing coil.
2. It can give status of last operation i.e. Close or trip.
3. As per standard practice Trip will always be on the left side and Close will be on the right side.
4. This can be locked in certain position mostly in Trip Condition so that it can not be operated
5. Some of the above listed features are requirement specific but a normal TNC switch breaker shall have all of the above except Point no. 4.
6. Normal Two / three position switch with spring loaded back to normal shall not be used as TNC Switch

Answer / vikas laller

IT is a three position Switch.When it is
in close position it will put the circuit breaker in
operation by energising the closing coil and when it is in
trip position it will trip the circuit by energise the trip
coil in circuit breaker.

Answer / sanket patil

A TNC SWITCH IS ALSO CALLED BREAKER CONTROL SWITCH. IT IS
LOCKABLE IN THE NEUTRAL POSITION AND IS A THREE POLE SWITCH.
WHEN IT IS IN CLOSE POSITION THE COMMAND IS GIVEN TO THE
CLOSING COIL OF THE CKT BREAKER AND THE BREAKER CLOSES.
WHEN IT IS IN THE TRIP POS COMMAND IS GIVEN TO THE TRIP
COIL OF THE CKT BREAKER AND THE BREAKER TRIPS.

Answer / amit tiwari

It is as simple as TNC (Trip Neutral Close) in normal condition the switch will be in NEUTRAL position. To close the Circuit breaker we have to rotate it in direction 'C' as mentioned in TNC switch and breaker will be in operation and if we want to trip the circuit breaker we have to rotate the switch in the direction of 'T' as mentioned in TNC switch and breaker will get tripped for maintenance. Remember TNC will operate from field. Remote closing and tripping can be done as TNC switch will be in 'N' position.

Answer / sunil kumar

TNC switch is a three position switch. when it is
in close position it will put the circuit breaker in
operation by energizing the closing coil and when it is in
trip position it will trip the circuit by energize the trip
coil in circuit breaker. But the switch After energize the coil it is going on in neutral position Automatically.

can a 12v dg starting battery(150 AH) be replace by 6 nos of 200AH batteries each of 2v connected in series.

3 Answers  

Why we can not get 100% efficiency from a Gas Generator?

1 Answers  

show that power dissipated by a pure inductor exited by a sinusoidal voltage source v = vm sin wt is zero

1 Answers  

why there is no current in the rotor body althrough the flux linking with it also get changes. why current only flows in windinds not in rotor

1 Answers   Vedanta,

how we can adjust for three phase motor cold stall time ,hot stall time and thermal register set up?

1 Answers   OPS,

What are the factors to be considered during the Synchronization?

3 Answers  

difference bteween neutral grounding resistor and neutral grounding transformer??

1 Answers  

why do MCB melt but not tripped in lighting highmast??

1 Answers   AHPCL,

What happens to voltage when current through the inductor is constant?

1 Answers  

whats the formula for convert KVAR to FARADS

2 Answers  

What is the purpose of earthing Truck ? How does it work for busbar and cables?

1 Answers  

What is the causes Power Factor become leading and what is the effect of Electrical system ?

2 Answers