Interested to Buy Any Domain ? << Click Here >> for more details...
in the thermal power plant, why we use the condenser (for
cooling the steam) when we have to heat the steam again.
i mean why we are cooling the steam,
- 6 Answers
- 10382 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / ghanshyam_singh
i think the difference in pressure is necessary to flow the
steam from turbine to again boiler.
and the process of condensation reduces the pressure. thus it
produces the pressure difference.
| Is This Answer Correct ? | 6 Yes | 3 No |
we maintain the temp. in plant and also to keep the excess
loss of steam at the end point by using which we increase
the efficiency of power plant
| Is This Answer Correct ? | 4 Yes | 2 No |
Answer / abolfazl ghasemi
Because Thermal power plant works in Rankin Cycle. And in Rankin cycle, the efficiency depends on the temperature and pressure in cold and warm points.(Boiler and Condenser).
And in condenser we distillate steam by spraying water on it to change it from steam phase to liquid and during this volume decrease (steam to water) we make vacuum or low pressure. So the surrounded area of the curve increases and efficiency goes upper.
Also we can save purified water. At the end we can add make up water and control the water demand of cycle.
Thank you for attending
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / k.prakashchandra
You mean reusing water ? You can fill the boiler with water
only.
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / k.prakashchandra
The outlet temp of the turbine is brought down to transfer
more energy as it is proportional to the difference in
temperatures according to the laws of thermodynamics.
| Is This Answer Correct ? | 1 Yes | 2 No |
Answer / rodney
Typically, a steam generator is a closed loop system.
Water is heated to steam, performs work(spins the turbine)
and then is condensed back into water. Its a continuous
system so the water is heated and cooled over and over
again.
| Is This Answer Correct ? | 1 Yes | 2 No |
how balanced in star delta connection ?
How can you justify a fully carged battery by physical checkup ?
12 Answers Indian Military Services,
WHY HUMMING SOUND OCCURED IN HT TRANSMMISSION LINES?
A 12.5 hp slip ring motor taking high initial current and its MPCB is getting open.what may be the reason?
Difference between SFU & FSU with advantantages & drawback?
what is the meaning of DSL
what heppend if we are connected u1-v1-w1 as a star point in the place of u2-v2-w2 in power genration
What is the operational principle of direct current current transformer and direct current potential transformer?if possible plz reply with ckt. diagram.
1) What are your personal strength? 2) What are your personal areas of improvement? 3) What are your expectations from from a particular job? 4) what are your carrier objectives?
What is the formuala to calculate the rating of motor protection circuit breaker
What are the components of feedback control system?
What are the disadvantages of LT AVR over HT AVR?
1 Answers APTransco, Jindal, TNEB Tamil Nadu Electricity Board,
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
