1. which type of transformer connection is preferred in
case of power supply transformers?
(A) Star/Star
(B) Delta/Delta
(C) Star/Delta
(D) Zig Zag/Star
2. In a power transformer usuall which winding is closer to
the core?
(A) Primary winding
(B) Secondary winding
(C) Low Voltage winding
(D) High Voltage winding
3. The power factor of a purely inductive load is
(A) Zero
(B) Lagging
(C) Leading
(D) Unity.
Answers were Sorted based on User's Feedback
Answer / pkv
deta /star transformer is used in case of power supply
trnaformer
| Is This Answer Correct ? | 11 Yes | 3 No |
Answer / koti
1. Star / Star
2. Low Voltage Wdg
3. Zero (Cos 90=0)
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / nadhagopal
star to delta
lagging for pure inductive
leading for pure capcitive
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / guest
in power supply transformers star delta conn. is prefered
| Is This Answer Correct ? | 3 Yes | 5 No |
1. Star/Delta Type of transformer connection is preferred
in case of power supply transformers.
2. In a power transformer usually Low Voltage winding is
closer to the core
3.The power factor of a purely inductive load is Lagging
| Is This Answer Correct ? | 2 Yes | 4 No |
Answer / moloy dey
1. In case of supply transformer DELTA/STAR is used to
ensure 440[Ph to Ph] and 220 [Ph to N] both type of consumers.
2. (A) Primary winding stays close to the core.
3. The power factor of a purely inductive / capacitive load
is always (A) Zero, Hence, the power drawn by a
pure/loss-less inductor/capacitor is VxIx'0' = '0' [Zero]
| Is This Answer Correct ? | 1 Yes | 5 No |
Why motor is not calculated in kva, whereas transormers are calculated in kva
How to synchoronize the generator (with gcb,GT) to grid????? ????? from Grid iam getting power (rated 400kv/20kv) through GT and its goes to UAT.,,ST.,, now my generator(rated 20kv ) ready.,, now iam closing my GCB.,, in GT iam suddenly giving 20kv on that Gt.,, what will happend
29 Which of the following breaking method save energy? A regenerative breaking B plugging C dynamic breaking D none of above
I am going to appear RRB Sr. Section Engineer Exam, Electrical. Can you send me previous year questions of RRB Electrical engineer. specially Section Engineer questions. my email id is likerahulworld@gmail.com
why we choose 50 or 60 hertz not other value for the power system?
what is meant by distance protection ? how distance protection relay function ?
The armature of shunt dc motor has 0.8ohm resistance and motor is to run on 120V circuit.If motor is suddenly thrown on circuit while armature at standstill then current drawn by motor will be??Also back emf in normal running is 110V
In Dyn11 power transformer if any one of the 3 phases connected to earth in star connected side then please explain effect of the current flow in delta connected side of transformer.(In this case if one phase is shorted to ground in star connected side then we observe the current flow in two phases only not three phases in delta connected primary side. Please explain why it is so?)
How to take the Vector Group Test in Transformer? What is the purpose of doing Vector Group Test?
What is the difference between a Distribution Transformer and a Power Transformer.
Resistance of low voltage side of transformer compared to high voltage side is A less B equal C more D depens on design
what is XLPE type cable
Civil Engineering (5086)
Mechanical Engineering (4453)
Electrical Engineering (16638)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)