what are the differenc between vcb and sf6 breakers
Answers were Sorted based on User's Feedback
Answer / raju
VCB means Vacuum circuit breaker Arc queching done in
Vacuum. SF6 breaker Arc queching done in SF6 Gas. And VCB
used for 11 KV to 33 kv but SF6 Breaker used from 33 KV to
400 KV.
Is This Answer Correct ? | 16 Yes | 2 No |
Simple vcb uses vacuum as arc extinguish medium where as sf6 cb uses sf6 gas as arc extinguish medium.
Is This Answer Correct ? | 14 Yes | 4 No |
Answer / kunjan singh
VCB can be used for upto 33 KV ,due to difficulty in
maintaining the vacuum inside a VCB at higher voltage,,and
also ,there are some size limitations...nowadays,at all
voltage level we can use SF6 CB having pressure of 5 to 6.5
kg/cm2..
Is This Answer Correct ? | 8 Yes | 2 No |
Answer / karthik_elec
vcb: its produce the vacuum during the on off and fault
duriations. this vacum eliminate the arc between the
contact points.
sf6: its pass the sulfer hexa floride gas during the on off
and fault duriations, the pressure of the sf6 gas inside
the circuit breker is 5 to 7 kg/cm2. it will vary the
operating voltage of the sf6 CB
Is This Answer Correct ? | 6 Yes | 2 No |
Answer / jayakumar v
VCB MEANS VACUUM CIRCUIT BREAKER 11 TO 33 KV IS APPLICABLE.
INSIDE OF THE BREAKER HAVING AN ONE VACUUM INTERRUPTER WITH CONTACTS. HERE VACUUM IS AN ARC QUENCHING MEDIUM. INSIDE OF INTERRUPTER VACUUM HAS BEEN CREATED BY MECHANICALLY (MANUAL) OR ELECTRICALLY(THROUGH DC MOTOR).
SF6 BREAKER MEANS SULPHURHEXA FLUORIDE BREAKER. IN UPPER SIDE OF THE BREAKER HAVING AN GAS POLE ASSEMBLY. INSIDE OF THE POLE ASSEMBLY HAVING AN MALE & FEMALE CONTACTS. ALWAYS MAINTAINING 3.8 Kpa PRESSURE INSIDE OF POLE FOR 33 KV LINE.THIS BREAKER RANGES UPTO 750KV.
Is This Answer Correct ? | 3 Yes | 2 No |
Answer / umashankar
AS we know VCB can use 11KV to 33KV where SF6 use 33KV to 400KV, also safety are more as comparing SF6 higher then VCB.
If VCB blast that damage more where sf6 not damage more for its SF6 gas.
Is This Answer Correct ? | 1 Yes | 1 No |
what are the interview question asked in wind mill about electrical
What is meant by time harmonics and space harmonics?
What is meant by load angle of an alternator? Upon what factors does the load angle depend?
I want to know which cable would be best to carry 125A current to a distance of 50m. Voltage is 3phase. Kindly share the formula with answer.
1 Answers Medway Educational Consultant,
1 ton aircondition(AC)consume how much watt?
what is Ith current?
which have higher efficiency transformer or induction moter
why single phase to grd test in HV cable?why not 2 phase at a time?
WHERE to use CVT & PT.
is that a problem if i connect a single phase load to a secondry delta connected transformer but i get a neutral from other transformer i the system?
Why are you like to join it job as a electrical engineering student?
4 Answers Bhushan Power Steel,
Hi,iam a diploma in electrical engineering.rtd from indian air force in apr 2007.prsently working in reliance next link as a network maintenance engineer since 2007,can i get a job in motherson sumi.
0 Answers Motherson, Motherson Molds and Diecasting Ltd.,