Answer / balaji

it will rotate in same direction as earlier

Answer / raj kushwaha

it will rotate in same direction as earlier and it will be
take leading current.
Like synchronisms motor

Answer / rm

the direction of rotation is anticlockwise due to motoring
action.

Answer / sukriti kiran

the direction of rotation wont change because the phase
sequence of the supply remains same as before(generator is
connected to infinite bus bar) , for magnetic locking field
poles develop torque in the same direction as before

Answer / arvind kumar

IT WILL NOT ROTATE,BECAUSE FOR LARGE MACHINE ARMATURE
WINDING IS PLACED on STATOR AND FIELD WINDING ON ROTOR,the
field winding is exited by dc.THE OUT PUT IS DRAWN FROM
STATOR,IN CASE ARMATURE WINDING WHEN CONECTED WITH GRID THEN
DUE TO INVERSE OF FARADAY LAW ELECTROMAGNETIC INDUCTION THE
ARMATURE WINDING WHICH IS PLACED ON STATOR EXPRIENCES TORQUE
under the influence of flux priduced by field winding,but
this is not possible to rotate the stator.for motoring
action is possible in small ac machine in which armature
winding is placed on rotor and field winding on stator
...read p.s bhimra page 239
ph7376722798

Answer / prashant kumar

alternators direction of rotatin is generally acw as it
rotates due to action of prime mover (steam,water)but when
accidently when it is connected with grid supply it stars
getting heavy curent to its wndg and starts motoring action
by rotating in cw(opposite) direction and its wndg gets
burned as it is designed for generation not for motoring action

Generator protection &generator test

1 Answers  

is there any device that works properly accept relay, it may be fuse but if i want fuse of 33kv 300 amp it is avaliable, pls give me details

0 Answers  

110 KW MOTER DOL STATER 240SQ.MM CABLE MOTER AND STARTER DISTANCE IS 110 METER WHAT IS VOTAGE IN MOTER END AND SYSTEM VOTAGE IS 415 V HOW I CAN CALCULTE

2 Answers  

in our sub station why we step down firstly 33kv\11kv then 11kv to 430v. can we direct step down 33v to 430.v.

7 Answers  

what is the function of capacitor duty contactor in an capacitor panel???

0 Answers  

How to calculate the actual 3phase power, if the load current of each phase is not balanced

2 Answers  

Three set (each phase contain 2 cable of 400 mmsq CU XLPE AWA) of single core cables are connected to 11 KV motor of 14 MW & the switch gear supplay is taken from 11kv feeder & this supplay taken from 275 KV substation. Problem is one pair cable(L3- 2 cable ) getting very hot & gland melted and damaged in switch gear side. the other two cable haven't any more hot(ambient temp only & L3 haveing 95- 100 Degree C. The same problem happened in 275 KV substation switch gear side also where the supply taken for 11 kv switch gear. But here L2 phese cable had problem. Why it is happening like this?. The cable having temperature different at different location from gland side inthe case of 11KV feeder of 275 kv substation. why ?

2 Answers  

What is a Single Phase and Three phase Power? How it will be converted or transformed into another form?

3 Answers  

what is mppt (maximum power point tracking ) and how they used in solar power generation ??? what are the main components used in mppt?????

0 Answers  

How to Make relay co ordination chart for a Electrical power distribution of a plant

0 Answers  

what is the difference b/w permitivity and permeability

1 Answers  

how one can check the Current of a DC 12 V battery ? Procedure. I told that take a thick wire (having more wires in it) and then join the + and - terminals of battery with the help of two ends of a thick wire .... is this correct or wrong .....

1 Answers