Interested to Buy Any Domain ? << Click Here >> for more details...
Why the earth terminal pin is larger than phase and neutral
in three pin plug top>
- 8 Answers
- 16166 Views
- TVS, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / selvam567
To make easy path to current while any short circuit
occured between phase to metal body of the equipment.
Note : The resistance is iversely propositional to the
cross section of the conductor.
| Is This Answer Correct ? | 19 Yes | 4 No |
At the time fault multiple time of the fault current is
generated so to give a proper path to the earth the pin
size is bigger in comparision to the other two
| Is This Answer Correct ? | 11 Yes | 2 No |
Answer / mechsatheesh
in larger size metal body have low resistance.it will allow
the leakage current faster to ground when compared to phase
current to draw inside.
| Is This Answer Correct ? | 5 Yes | 1 No |
Answer / abhik raj
becz it designed in such a way that line never be shorted
to earth terminal by mistake no one can insert the plug
with out any other combination ...otherwise the neutral
point may be inserted to line which may cause serious
accident..
| Is This Answer Correct ? | 6 Yes | 4 No |
Answer / praveen kotha
We know that the resistance is inversely proportional to area of cross section.so if area increases resistance decreases,so the leakage current will take low resistance path.that is why earth pin is thicker.
It is longer because the first to make connection and last to disconnect should be earth pin,this will assure safety for the person who uses the electrical instrument.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / akem gilbert
The reason is simply to ensure that the ground connection is the first to make when plug is inserted and the last to be broken when the plug is removed.
| Is This Answer Correct ? | 0 Yes | 0 No |
You can insert the top in one way only ,so that the phase
and neutral wires are not interchanged and also because the
earth fault current could be higher than the load current
| Is This Answer Correct ? | 2 Yes | 3 No |
Answer / pandu
some times the variation in supply voltage the load takes
high current to overcome this problem the earth terminal is
placed
| Is This Answer Correct ? | 0 Yes | 5 No |
Power Factor Correction Panel (Manual & Automatic)
Name two types of electrical analogous for mechanical system.
WHAT IS THE DIFFERENCE BETWEEN NUTREL AND EARTHING
what is creep of energy meter?
WHICH TYPE OF TRANSFORMER IS USED IN POWER TRANSMISSION BASED ON TRANSFORMER CONNECTION ON PRIMARY AND SECONDARY SIDE
why in an electrical lab a bulb connected to supply goes off slowly when the main supply is switched off?
1.why we are using metal oxide gapless block in lightning arrester,2.What is minimum and maximum rating of metal oxide blocks using in india
If two generator running parallel, at that condition both ngr Taken in line or taken any one ngr, but why any one or both Ngr in line? Ngr is use for which purpose?
what is the signification of trivector meter? why its name is trivector meter ?
What is current divider rule (cdr)?
what is the type of motor that is used in emu units in india
WHY IN AC DRIVES,INPUT PHASE CURRENT SHOW UNBALANCE?
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
