Answer / namadeo bhangire

It is an device which help to discharge the high
voltage.rod type is used in industry.to discharge the high
voltage

Answer / saiyed moinuddin

It is the device which is used for over voltage and
specially used for lighting stroke

Answer / ashokkumar

Lightning arrester is the device to protect the Equipments
and buildings which is located in very hight. Lightning
stoke is attack the tallest point in the area. So we are
mounting the lightning arrester at the highest level and it
will grounded through proper arrangements and accessories.
Mostly GI is used and the best one is copper arrester. This
copper or GI is connected with downleads or down conductor
and it terminates to the Lightning Earth pit. To avoid the
lightning damages we are using the lightning protection system.

Answer / amar shah

Lighting aresster(Surge arrester) is used for protction of
elctrical equipments(i.e. Transformer, Circuit
breaker...etc) against lighting strok. it is available in
two type. Gap less Arrester (i.e. Zno arrester) & with Gap
Arrester (in air). when its maximum continues operating
voltage exceeds it will get shorted(Non linear
charactersitc) and the lighting strok passes through it o
earth, without damaging the equipment next to it.

Answer / m.jagadeeshraja

The Lightning Arrester is used to prevent the particular
component(consider Industry, Shops, Home,.. etc). When
clouds collided each other the charger present in clouds are
discharged, when these forms lightning(in terms of MEGA
AMPS)and fall where the low potential areas. So Lightning
Arrester made as low potential and less resistance path so
these charges are DUMPED here.

Answer / s.mahaboob basha

LA has discharge the High voltage to earth .In industry
Thyristor type lighting arrestor used ,because of in this
rod gaps are there. This LA rating has 10KA

Answer / satvir singh

Lighting arester is the matelic (mostly copper made)
arrangement/device or we can say like antina in the shape of
Hunuman G gadha type , Trishul type, Road Type. which used
for grounding the lighting surges or can say the Heavy
Current flow from sky in raini days. Its provide the
shortest path for Heavy Current flow in minimum time
without damageing the building ,Equipment , through copper
wire/GI strip-clamped and connecte in to the earting pits
in which the Earthing had done already like GI/Pipe/Plate/
Gel earthing .out side of Building,chimini etc. it is
mounted on top up of the object according to safetty point
of vew, size ,area wise

Why distribution transformer secondary voltage is 0.433kV instead of 0.415kV.all other switchgear rating are 415 volt??

3 Answers  

how to prepare PPM schudule

3 Answers   TATA,

A ii kv 1200 A Breaker combination fixed in a cubicle. How many ampere Fuse is required? If fuse is not using, Why?

1 Answers  

IF HT CAPACITOR IN ON POSITION IS THERE ANY LOSSES I.S I SQURE OCCURS IN THE SYSTEM

1 Answers  

it is difficult to interrupt a capacitive current because (a)it has a leading power factor (b)current magnitude is very small (c)the restriking voltage can be high (d)stored energy in the capacitor is high

2 Answers   DGVCL Dakshin Gujarat Vij Company, MGVCL, UGVCL Uttar Gujarat Vij Company Ltd,

2 Diesel Generators 900KVA connected to the bus bar for essential load as an alternative for power taken from 11/440V 3KVA Transformer supplying this bus bar. my question here is in the event of power failure on 11KV side can I feed the power to 11 KV bus by using the same transformer as reverse feed, what will be the inrush current???

3 Answers   Ashok Leyland,

Earth leakage relay basic knowledge principle

1 Answers   Radiant,

1 tr is equal to how many Kw .is there any specific formula for this to get the result .

13 Answers   Cipla, LG, NSN,

in thermal power plant the steam produced is made to cool after falling on the turbine blades. my question is why this is done while the same is needed to heat up again. "jab pani ko wapis garam hi karna hai to thanda kyu karte hai"

11 Answers   Bhel,

when we conduct high voltage testing why milli amp. is required?

2 Answers  

WHY IS HV WINDING OF A TRANSFRMER SECTIONALIZED???

3 Answers  

what is a breaker fail relay

0 Answers   Eskom,