Answer / aasha

nuclear power plant

Answer / d. tushar

Dear Friends,
i suppose the question was misunerstood by some persons.
The Plant Load factor is the term which means the output of
the power plant with respect to its rated output. (actual
o/p / Rated o/p). Generally PLF term calculated annual basis
(Viz. If a power plant have rated o/p 250 MW i.e. 250x24(hr)
x365(Days) (annual o/p) and its actual o/p is
250x24x340i.e. its o/p is less than its rated o/p )
most of the plant have PLF in between 65 to 100 %. the PLF
depends on power demand,maintanance outage of plant,forced
outage,actual plant generating capacity,etc.

Now the ans of the question asked by ms. asha
PLF not de[pend on type of power plant. but obviously PLF
of thermal,nuclear,gas power plant are higher than non
convential power plants. Thermal power plants can give PLF
more than 100%.If it operate at higher the rated capacity
(e.g. Dahanu Thermal Power plantsPLF is above 100%)

Answer / nithi

All base load power plants(thermal,nuclear & hydel (during
rainy season)) will have a high load factor.

Answer / nithi

All base load power plants have a high load factor.

do you agree?

If we use high efficiency power plants to
supply the base load,we can reduce the cost of generation.
Hydel power plants have a higher efficiency than
thermal & nuclear power plants.
Then why can't we use hydel power plants as a base
load power plants during rainy season?
But,all friends are concentrating only on nuclear
power plants.I don't know why?

Answer / vksumanth

nuclear power plant because ,this plant consumes less energy for generating high power.

Answer / kapil

The Power plant whioch are running on base load, having
high Plant Load Factor

Answer / ritesh

the ans can different that given here because the total
power factor is depend upon your generating power plant
that how much it generated and how much power required to
your area.

Answer / guest

nuclear power plant

Answer / meenakshi

hi ppl, both nuclear and thermal vil ave a power load factor
(PLF) in the range of 60%-85% .n the overall PLF i.e,
considering all the thermal power stations,it is 77.5% but
for nuclear it is around 61%.so,ave u guezzd the answer?
s . its THERMAL POWER PLANT.in case of any improvement in
the answer,plz do notify me...gud luk..

Answer / bat-erdene

Dear Friends,

If we improve power factors of high voltage (6kV) motors for
own demand of a power plant fired coal,

will the electric energy distribution of the power plant
increase?

can you tell me/show me, how to manually synchronize 2 DG. preferred with video.

2 Answers   Cummins,

will 1050kva DG set withstand for back charge of 16MVA transformer

0 Answers  

what is difference between vaccum circuit breaker and air circuit breaker?

2 Answers  

Why high Voltages come in multiple of 11, like 11 KV, 33KV, 66 KV, 132 KV etc.

11 Answers  

witch pump used in wtp

0 Answers   Dalkia,

how the CT and PT is connected in the circuit during testing of transformer explain with diagram

0 Answers   KESC,

How we connect capacitors in Fixed Series compensation of AC transmission lines. Whether in parallel or in series?

3 Answers  

Determine the MVA rating of the power transformer given that 110/66 kV,1000 Amps. Folks how can i calculate the MVA rating with this Data??Plz Help........

1 Answers  

what will happen power cables laid without gap in underground

1 Answers  

Arrangement of earthing materials.like what we put first charcol,then salt.then plate. Plz answer me about that.

1 Answers  

How to calculate pitch, gauge of winding wire, and No. of turns for 30HP, 3 phase, 4 poles 50Hz, 380V induction motors

0 Answers  

What type of fittings and electrical accessories can be install in radiation area ?

0 Answers