Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
Plot the pixel histogram( take any image) – count of values versus pixel intensity 0 to 255. You must write this from first principles – do not use the MATLAB hist command (although you may use it for comparison and checking your algorithm’s correctness). Plot the cumulative histogram. Do not use the cumsum function in MATLAB (write your own function to achieve this).
2039Hello sir, I am Rajaram. I have finished DME (Diploma in Mechanical Engineering). I would like to attend BHEL supervisor examination. So i want which type of questions can i prepare. & give previous supervisor examinations questions. Reply my mail (rajaramsptc@gmail.com)
Bhel,
4206How the electric train gets the supply of electricity? What is the return path of the current?
NTPC,
7 16297When looking at a flanged extension pipe and it is labeled DN20, just what does that mean or intel?
2280
what clearance required for 4.5 mva dry type transformer?
What is costing in 100squre feet bricks
How to calculate concrete in percentage wise ,for example cement 18% sand 40% aggregate 40% and Stell 2% ,I need and??
If you had a cylinder, sealed at both ends, with the pressure rising inside, would it blow at the end or split along the side first?
Explain what will be the responsibility of the spacecraft operations, dynamics and controls?
Explain me what is silk fiber?
what is feed back and what are feed back amplifiers?
What is a bearing? What are the different types of bearings?
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
5.WHICH TYPE WELDING PROCESSES USES NON CONSUMABLE ELECTRODE.........
Discuss about WAP architecture in detail.
for 100 HP Induction motor service factor is 1.2(SF) we placed a VFD at the motor side load is balance with 0.3 Amp's Phase to Phase but at incoming of VFD load is un-balance with 10 to 20 Amp's what will be cause of load un balance
I am a diploma Automobile Engineer working in Volkswagen for 4 years . I wish to apply for Australian PR however SOL of austria does not include automobile ngineering is there any other way i can choose to apply for the same. Please help..
Why is using C language
what energized you to complete your course?
