How can you test the vector group of power transformers?

Answers were Sorted based on User's Feedback



How can you test the vector group of power transformers? ..

Answer / thowsif_emerson_csm team

A Vector group is the International Electrotechnical
Commission (IEC) method of categorizing the primary and
secondary winding configurations of three-phase
transformers. Within a polyphase system power transformer
it indicates the windings configurations and the difference
in phase angle between them.[1]

The phase windings of a polyphase transformer can be
connected together internally in different configurations,
depending on what characteristics are needed from the
transformer. For example, in a three-phase power system, it
may be necessary to connect a three-wire system to a four-
wire system, or vice versa. Because of this, transformers
are manufactured with a variety of winding configurations
to meet these requirements.

For More Information Log On to:-

http://en.wikipedia.org/wiki/Vector_group

Is This Answer Correct ?    2 Yes 0 No

How can you test the vector group of power transformers? ..

Answer / ashwani malhotra

(2u-2n)+(2n-1W) = (1U-1W)
( 2v-1W ) = (2w-1W)
( 1V-2v ) < (1V-2w)
( 1U-2v ) = (1U - 2w)

In DYn11 connect 1U & 2u .and apply the 3 phase 415 v ac to
HV side. Check for the above condition .if its ok then
group is DYN11.

Is This Answer Correct ?    2 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

a 3 phase motor was running with delta connected, suddenly one phase winding got burnt off, what will be the effect ?

8 Answers   Bhel, RRB, SR,


line tester lamp working in which voltage?

3 Answers  


if we increase frequency of line, then how will string efficiency varies with it.

2 Answers  


which transmission is cheaper ac or dc?

10 Answers  


why capacitor burst?

2 Answers  






What is cut-off rate?

0 Answers  


how moving coil indicator works?

1 Answers  


How can w select the cable size for different rating load & also waht r factors affecting the during selection of cable?

11 Answers   AB Inc, Bosch, BRB Cable, Lucas TVS, Trisome Technical Services,


Define filter?

0 Answers  


Explain the functioning of diode?

0 Answers  


If the ceiling fan is on slow speed, does it consume less electricity?

2 Answers  


I am having a DG set.The 415 V from Generator is step up to 460 v and then the same is used for Induction furnace. before Step up, I am connecting LT load to my factory use. When Induction furnace is in service from DG, when i try to start a motor, the generator is tripped.Please tell me the reason.

3 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)