without any theoretical calculations, can u approximately tell the current rati

Categories >> Engineering >> Electrical Engineering
Suggest New Category

without any theoretical calculations, can u approximately
tell the current rating of a motor(above 30hp)working at 415VAC.

Question Posted / phanidhar

7 Answers
7433 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / venu

As per thumb rule the current rating of a motor working at
415vac
equals to double the KW rating (and -2% of double the KW)

Is This Answer Correct ?

5 Yes

1 No

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / shahid

Thumb rule to calculate the current of all d LT ac motors
is:

A = 1.7*KW

Is This Answer Correct ?

5 Yes

1 No

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / azarudeen

Above 40A (if efficiency of motor - 90% & PF - .8)

FORMULA: I = (HP*746)/(1.732*415*Eff*PF)

Is This Answer Correct ?

4 Yes

3 No

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / dheeraj soni

As per thumb rule motor working at 415 ac their current
rating is aprroximately 1.5 times of its HP Rating

Is This Answer Correct ?

2 Yes

1 No

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / arsenal

actually how is the thumb rule obtained......is there any
derivation.........

Is This Answer Correct ?

0 Yes

0 No

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / yogender goel

As per the Thumb Rule,

Current = (Motor HP x 1.5)-10% of the total

Example: If we want to calculate the current of the 100Hp
motor then
current = (100 x 1.5)-10% = 150-15 = 135 Amp.

Is This Answer Correct ?

0 Yes

0 No

without any theoretical calculations, can u approximately tell the current rating of a motor(above ..

Answer / m. madhu sudhanarao

As per thumb rule Motor current rating at 415AC is
approximately 1.6times the KW rating.

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

What is OLTC in a transformer, specify its fuction.

35 Answers Bhel, Isgec, L&T,

although ckt breakers have taken the place of old fuse. But instead of it , these older ones are still used in the industries and homes ? why .... what are their advantages and disadvantages ? which one is leading and winning the race and competition ?

0 Answers

1. What is differential relay? How it operates?

3 Answers

why we r using 4-20ma instead of 0-20ma in instrumentation

2 Answers EID Parry,

can we choose current transformer secondary, to calculate residual flux in a power transformer, so as its saturation is close to the saturation level of power transformer?

0 Answers

can u name the different types of motors used in different types of applications?

6 Answers ABB, Bhel, SBQ,

What are the diferences between ELCB and RCCB

5 Answers L&T,

WHY THE FREQUENCY IS 50 HZ IN INDIA.CAN WE USE SOME OTHER FREQUENCY.IF SO WHAT IS THE RANGE AND WHAT WILL BE THE EFFECT IN PRESENT POWER SYSTEM IF WE CHANGE THE FREQUENCY AS YOU SUGGEST ?

32 Answers L&T, MCL,

why a pilot exciter is used in combination with the main exciter? why not only a main exciter is used for excitation to an alternator?

1 Answers Electrical,

why battery dc voltage become Half when we check with respect to ground for example 120volts + and - terminals and when we check + terminal with Earth thats 60volts why 60volts same result on 24Volts and with ground 12Volts only expert answer that thanks we can not ground the battery.

2 Answers Etimaad,

what is means of ALF,kPV(min),lexc(max)at Vk,Rct@75 degree centrigate ohm in current transformer name plate?

2 Answers

what is the problem in manufacturing transformer with 0 degree phase displacement.???why alwasys go for DYn11 or DY5?Whys not DY0 i.e zero degree displacement between primary and secondary side vectors?

3 Answers Bhel, dpdc, Prime Electrical,

For more Electrical Engineering Interview Questions Click Here