why breather cap filled with oil?
Answers were Sorted based on User's Feedback
Answer / suresh ( kakinada)
Answer 1 (Gove) is correct. To filter the dust particles
which enter in to the breather. I have seen 2 type of
silica gels 1. Normal colour Blue after collecting moisture
it turns to Pink colour.
2. Normal colour Orange after collecting moisture it turns
to Green.(imported silica gel).
Is This Answer Correct ? | 22 Yes | 0 No |
Answer / gova
Hi
To filter the dust in the atmospheric air.
Kind regards
gova
Is This Answer Correct ? | 22 Yes | 3 No |
Answer / srinandan
The sole purpose of oil cup in breather is to absorb dust particles in the air which is going to transformer. Silica gel absorbs moisture and oil cup absorbs the dust particle.
Is This Answer Correct ? | 3 Yes | 0 No |
Answer / chandrasen mourya
If it is directly exposed to air it will become pink &
hence cannot be used. Its purpose is only to allow the air
trapped in the tank to be released thrg it.
Is This Answer Correct ? | 2 Yes | 11 No |
Answer / sumit srivastava
it is filled with oil so that even if breathing action is
not occuring ,the oil is prevented from absorbing
moisture.So when breathing action occurs silica gel takes
care of the transformer oil and in idle conditions it is
protected by oil.
Is This Answer Correct ? | 1 Yes | 11 No |
Answer / senthil ganapathy
Is breather usually filled with Silica Gel....?
I think its not oil..
Is This Answer Correct ? | 4 Yes | 17 No |
Answer / raj yadav(allahabad)
silica gel is filled in the breather and good condistion of
silica gel colour is pink
Is This Answer Correct ? | 0 Yes | 17 No |
what is the signification of trivector meter? why its name is trivector meter ?
7- What is the Dissipation Factor and the difference between it and Insulation Resistance Test? 8- What is the task (function) of DC and AC reactors in power plant? 9- What is the task (function) of (open delta with earthed) in some types in transformers? 10- What is the base of the selection of the vector group in transformers? 11- What is the zig-zag transformer and its function by drawing in large detail? 12- What is the polarity ? 13- Why we make short between phase(R) in high side and phase (r) in low side in vector group test? Where High Side ( R ,S and T ) and Low Side ( r ,s and t ). 14- What are the time on delay and time off delay? 15- What is the vector group? 15- What is the task (function) of different types of vector group such as Dyn11 , Dd0 , YNd1,……..,?
Explain about Leakage Test.
Where we use 30mA , 100mA & 300mA RCCB ?
what is bus duct and what is differance between bus duct and bus bar
What should be the setting of an earth fault relay.
How can transformer oil be used in transformers with voltage rating above its breakdown voltage?
Sir,In our company there are 3 caterpillar make(capacity:(1) 3.3KV,2.5MW(2)3.3KV,2.5MW & (3)3.3KV,1.9MW) & 1 deutz make (capacity:11KV,3.8MW)gas engines utilised,all are running in paralell. There are three transformer utilised,(1) 6.25MVA,3.3KV/22KV,Impedence voltage:6.7% used for two generator,both are 2.5MW(2)5.5MVA,3.3KV/22KV,Impedence voltage:7.2% used for one generator of 2.5MW & (3) 5.5MVA,11KV/22KV,Impedence voltage:7.8% used for one generator of 2.5MW.all generator breakers capacity of 1250Amps. Sir,I want the details of fault level calculation of generator,transformer individually & for whole system. If you require any information from me.feel free for contact me sir.pl.send the answer of my question as the earliest as possible.
What is magneto on a gas generator. how it functions. its out put is d.c or a.c. how it can be checked for correct functioning
Megger type of instrument is used to check??
ELECTRICAL DRIVES: can a motor load system with passive load torque can have equilibrium speed in second quadrant
What is the difference between in Fourier series and Fourier Transform. and please tell me the difference between both of them and the why we use them in communication system?