what is the working of ups.

Answers were Sorted based on User's Feedback



what is the working of ups...

Answer / md. zakir hosen

UPS means Uninterruptable Power Supply. Its function is to
convert AC power into DC and store in a Battery when AC
supply is interrupted (no electricity, under voltage or over
voltage) then UPS act as a power supply by Inverting DC to
AC from the charged Battery.

thanking u
z_hosen@yaoo.com

Is This Answer Correct ?    11 Yes 3 No

what is the working of ups...

Answer / ponnamalla venkata satish

ups means uninterpted power supply it is play very
important role in industrial process because the field
intruments should give continous signal to the control
system and if in case power has shut down due to abnormal
condition in plant then also control system need some
process parameters to avoid hazards so ups can give
continous supply to the field instrumens and as per the
requirment in the process

Is This Answer Correct ?    3 Yes 1 No

what is the working of ups...

Answer / gopal lal

UPS mans untriptable power supply if power failed or two
phasing U/O voltage of the supply UPS given the power
backup.

Is This Answer Correct ?    2 Yes 1 No

what is the working of ups...

Answer / sunil guru

BASIC USE AND RUNNING OF UPS IS WRITTEN ABOVE ....
LET ME GIVE SM DETAIL EXPLANATION

UN-INTERRUPTIBLE POWER SUPPLY(UPS)---- HAS BASIC 6 CIRCUITS FOR ITS COMPLETE WORKING

1> MAINS UNDER AND OVER VOLTAGE CUT-OFF CIRCUIT
2> BATTERY CHARGER CIRCUIT
3> RELAY CHANGE OVER CIRCUIT(FROM MAIN TO BATTERY MODE-IN ABSENCE OF UTILITY)
4> BATTERY DEEP CUT OUT CIRCUIT (AT LOW BATTERY THIS CKT WILL CUT OFF BATTERY FROM CKT)
5> INVERTER CONTROL CIRCUT (CONVERTS FROM DC TO AC)
6> POWER OUTPUT STAGE (WITH THE HELP OF TIMER(555),TRANSISTOR AS A SWITCH AND USING MOSFET OR IGBT WITH APPROPRIATE DRIVER TO SWING DIRECT CURRENT TO ALTERNATING AT 180 DEGREE PHASE DIFFERENCE AND PRODUCING 50 HZ FREQ WE CAN DELIVER THE 220 V AC POWER

FOR ANY DISAGREEMENT OR MORE IMFO CONTACT ME ON PARMAR20072008@YAHOO.COM

Is This Answer Correct ?    2 Yes 1 No

what is the working of ups...

Answer / mk

it is a uninterpted power supply it will be use when
normal supply are fail. it consist of three part which is
rectifire battary & invertsr in normal condition normal
supply given to this device battary chanrged from this
supply & when normal suplty is gone then load oprated in
battary supply

Is This Answer Correct ?    0 Yes 2 No

what is the working of ups...

Answer / venkatesh sk

ups meains un innterrpited power supply function
convertor&invertor convertor means achigh voltagetodc
low voltage battery 12v & invertor high voltageto battery
used emergency back storge power

Is This Answer Correct ?    4 Yes 7 No

what is the working of ups...

Answer / chethan

ups means uninnterrepted power supply , to main tain the
constant volage & to avaide shutdowning the system.

Is This Answer Correct ?    1 Yes 6 No

Post New Answer

More Electrical Engineering Interview Questions

On Which Pressure PRV is operated.

0 Answers   AEPL,


Current chopping mainly occurs in air blast circuit breaker.why?

1 Answers  


How to test the Secure Elite 440 Multi function meter working condition.

0 Answers   Sadanand Constructions,


actual rated capacity of a disc insulator??

5 Answers   OPTCL,


WHY TRANSFORMER IS MEASURED IN KVA?

10 Answers  






if 40 watt bulb has higher resistance then a 100watt bulb then according to joul farmula p=I^2R the 40 watt bulb more power consume then 100 watt bulb.

5 Answers  


Define conversion efficiency of a power amplifier.

0 Answers  


srij i need the relationship b/w KW AND KWH and with an electrical example. plz send if u can?

4 Answers  


with 3 phase board on a 63 amp rcd is it ok to have 6 electrical showers 2 on each phase and what problems could happen

0 Answers  


Why tripping not occur when the transmission breaks? Doesn't we provide earthfault protection for it?

1 Answers  


We have 800KW motor operating at 6600Volt,50 Hz supply.During 1st startup it tripped on overcurrent trip.It's FLA is 88 Amps.The K factor of Thermal overloaaad was set on .94 initially.then we set at 0.97 and then it started fine.i dont understand why it tripped first?What are the protections which comes in picture during starting ?

6 Answers  


if there is fire alarm,what is ur activity?

4 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)