Interested to Buy Any Domain ? << Click Here >> for more details...
Explain the advantages of the wheatstone bridge method of
measuring resistance?
- 7 Answers
- 55059 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / sunitha thomas
disandvantage:-the wheatstone bridge is not applicable for
high resistances
advantage:-1)it shows a null measurement(i.e.-potential
differnce across the end points of the bridge is zero)
2)since it is an arrangement of 4 resistors ,it is useful to
find one of them in terms of other 3
| Is This Answer Correct ? | 97 Yes | 14 No |
Answer / satya hari krishna
It operates on null deflection i.e., indication is independent on indicating instrument's characteristics.that is reason it has high degrees of accuracy.
| Is This Answer Correct ? | 26 Yes | 9 No |
Answer / jvino03
Wheatstone Bridge Consist of 4 Resistance.. Out of Four
Resistance three are Standard one.. and one will be the
varying nature.. if bridge is balance only the variable
resistance equal to the standard resistance,.. through
galvanometer we observe the changes...
| Is This Answer Correct ? | 16 Yes | 5 No |
Answer / yoyo agrawal
wheatstone bridge is most accurate method available for measuring resistance.
| Is This Answer Correct ? | 14 Yes | 3 No |
Answer / ravi prakash.u
advantage of Wheatstone bridge:to find the unknown resistance value and simplicity of circuit
designing
disadvantages::based on temperature and power supply the resistance value will be degrades
| Is This Answer Correct ? | 14 Yes | 5 No |
I have carried out wiring for lighting in a shed in Industrial area which contains Metal halide lamps & have balanced in 3ph.Now when we put all the lines on in the daytime the current taken at 3phases at MCB comes to be equal i.e.28,29,28Amps respectively but in the night time i.e between 7p.m.to 11p.m. at the same MCb the current is 52,59,62Amp, though I have fit 63A MCB it is tripping in the above period.What may be the reason.? Note: This industry is located in industrial area where majority of steel ingot manufacturing plants are there. Whether this may be due to harmonic? what should I do to overcome above problem.pl suggest urgently.
what is main reason for grid earthing for any industry
how can we make cable shedule for controll wiring ? which details must be required for it.?
how calculated Transformer losses.
can we connect both delta and star to the transformer secondary and for what reason?
What is the SPEED of electricity?
what will happen if earth of 33 kv cable (earthed system) is not connected to earthing pit?
WHAT IS EDDY CURRENT LOSSES AND SKIN EFFECT LOSSES IN ELECTRICAL ENGINEERING
In a 11Kv/433Volt Delt-star step down transformer one one line(Line-B) of HT site is open & earthed on DP structur. What will be the voltage on LT side R-Y, Y-B,B-R and R-N, Y- N & B-N?. Please help to understand the problem with examples. Arvind , Jaipur.
How can we calculate No load and full load torque of electrical machines, i.e. motor or alternator?
at what rate the micro controller increment its timer....is it 1micro seconds or 1/(12*10^6) seconds
How much pole motor can be desion for 415 volt ,50 hz.Power supply. in pratical condition . Prakash veer singh
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
