Answer / ali raza

As we know that N=120f/p from here we can eisly suggest
here that moter pole depend on speed and frequincy not on
voltages there4 we can not suggest motor pole

Answer / biswajit sahoo

unless you are not mention rpm you can not predict no of
poles with voltage and frequency

Answer / uttam kumar sarkar

Motor pole dipenda upon Speed(N),Frequency(f).
Now we know the Syschronous Speed N=120f/P,
where P is No. of pole,
If synchronous Speed N=1500,
then P=120f/N, where,N=1500rpm,f=50.
P=(120*50)/1500
=4

So the No. of pole will be 4.


thanks to all
Uttam kumar Sarkar
email; engrutm@yahoo.com

Answer / thowsif_emerson_csm team

Normaly its 4 Pole.

Answer / prakash veer singh

Dear Ali
I know better that Motor supply voltage rating is not
depend on motor pole nombers .its depend on motor winding
turn.

WHAT IS FORMULA TO KNOW TO BACKUP TIME OF POWER PLANT 48V/50AMP DELTA POWER PLANT

1 Answers  

What is the two pole structure?

0 Answers   Foxconn,

Energy metering: On the property I am renting, the supply voltage is 2 x 110 volts. These 2 x phases enter a energy meter which then exit the meter to over head lines to my house. Question 1. The meter is single phase 240 volts but is being used as 2 x phase(2 x 110volt), is this acceptable? if not, please give me the reasons. The meter details are as follows: 60Hz 15amp Imax 100 amp Kd 3,6 Wh/R 1 fase 3 hilos Model FX 231. I think it was manufactured in Brasil From this meter, the cables run along over head aluminum conductors,I estimate the cross sectional area to be 25mm diameter, but the neutral is only about 10mm square diameter, which cover a distance of 170 meters and then terminate with an underground cable of 65 meter length, total length = 235 meters. There must be a huge voltage drop over this length. This line is protected with 2 x 200 amp aluminum fuses after the meter, there is no main switch in the distribution board. These 2 phases connect directly onto 2 busbars. Surely the neutral should be the same size as the conductors if not more? Question2. What are your thoughts about this installation, should there be better protection, is the neutral too small? During the night, the lights dim then brighten all the time, this cannot be good for my electrical appliances. In my home, I only have a small electric geyser and fridge, my stove works off gas. But when i use other appliances like the washing machine or microwave oven, the light dim. The internal wiring of this house is done with solid hard drawn copper wires and of course, they have to be under rated. I am a retired electrician by trade, but not on the metering and over head mains side, my experience is on the factory maintenance side of things. Your expertise on these matters will be greatly appreciated. Please inform me how to rectify or make any improvements Kind regards, my power bill is very expensive, so I need to know how to bring it lower. Kind regards, Brian

1 Answers  

Why is making current of CB always greater than CB breaking burrent?.

6 Answers   JP Group,

What is the method to solve circuit using source transformation?

0 Answers  

Why we do 2 types of earthing on transformer (ie:)body earthing & neutral earthing , what is function. I am going to install a oo kva transformer & 380 kva dg set what should the earthing value?

0 Answers  

what is neutral grounding? why is it required? what is neutral grounding resistor and how is its value calculated??

11 Answers   NTPC, ONGC,

how to select the double earth conductor if 21A full load?

0 Answers   L&T,

What is Phasing out test?

1 Answers  

why motors are rated in HP?

3 Answers   HCL, ncpl,

list the type of vfd? wich is sutable for heating kiln?

0 Answers   AluChem,

why voltage rating not mention at HPSV or HPMV lamps?

2 Answers   OPS,