Answer / raj

instrumentation is the measurement and control of any
physical parameter that changes w.r.t time.Its need is to
control any time varying quantities in the industies.The
characteristics of the inst.engg is to predict the changes
in the parameters and control accordingly.

Answer / yatin

hi

Instrumentation field born with the process plant. in
process plant need to maintain the temp,pressure etc. for
that purpose. so various type of instrument use for it.

characteristic of IC engineer to understand the process of
any plant and know which instrument use to control the
process and try to make it ok.

Answer / karim

Instrumentation is the branch of ingineering which deals
with measurement and control of all process variable.such as
pressure,temparature,level,flow,ph,conductivity etc.
to run any industry in safe and accurate with in limited
resources ,we must need this instruments.if the istruments
are not there,what happening in the process we don't know.

Answer / alfred t jose

instrumentation is the field to measure,control and
recording any physical parameters. actual need of
instrumentation is to control and record of parameters for
controling and for future purpose respectively.

Answer / raja

In addition to above pts,
Instrumentation and vital
need is mainly due to need
for
calculative,quantitative,quality,productivity,safety
of any process & so I&C
Engineer does thru
measuring,recording,monitoring
& controlling.

Answer / apoorv

instrmentation is a term in which we simply deal with the
instruments,it is needed for measuring,recording and
controlling.

Answer / jj

inst deals with monitoring, measurement & control of a
particular process..instrumentation engg needed mainly for
optimizing a particular process..

Answer / shakeel ahmad

Instrumentaion is the branch of Engineering, which mesure
of physical and chemical property of the material.that is
known as Instrumentaion.

Answer / raj

measurement.

Answer / ruban

instrumentation is the field which is used to study about
measurement and control process of equipment lik, plc,scada
and strain guage also it will go thrw thr process of
flow,pressure and temperature of the particular
innstruments which we r going to deal with this.

yokogawa Temperature transmitter showing Error 15 which is Reverse Cal Fail (confirmation calculation result is bad) in manual they mentioned reasion That the output goes to the value set by hardware failure mode jumper. How can solve this problem ? anybody can say solution

1 Answers   GTL,

What is pipe schedule? What are all effects its having in the valve? how do we take care of pipe sch in case if the customer dint specify in the data sheet. What we need assume and in what basis?

3 Answers  

what is the input to be given digital temp controller during the the calibration time?

2 Answers  

For crude application in floating roof tank, how to calibrate a DP Transmitter? How is the floating roof weight considered?

0 Answers  

Why only negative 24 vdc supply give in vibration measuring system.

6 Answers  

A differential pressure transmitter is configured to measure the height of an open tank : height 10m and dia 5m. Suppose this same transmitter is shifted to another open tank : height 10m and dia 4m. What will be the %error in measurement? how?

3 Answers   McCoy Engineering,

What is DCS?

5 Answers   Adani,

as an instrumentation engineer which are the things we have to know / or we must have idea about that....

2 Answers  

when the instrument tapping on pipe line is located below and transmitter is located above the tapping point for liquid service transmitter, what should we do, is there any additional drain valve is required??

2 Answers  

in split range control valve,two valve should be in two different line and that should have some distance,and we have only one positioner feed back link.so how we connect one feed back in two control valves?if you have picture please forward me.my email id kb.syamkumar@gmail.com

2 Answers  

List three types Level Transmitters with their working principles

1 Answers   ABB, Bapco Bahrain Petroleum Company,

plz tell me clearly about PID.."when v have to change I value,D value,GAIN??

0 Answers