In an LT pole, the line voltage is 415V. How is it converted to 230V into the

Categories >> Engineering >> Electrical Engineering
Suggest New Category

In an LT pole, the line voltage is 415V. How is it
converted to 230V into the house via the service cable?

Question Posted / larvabanton

10 Answers
18246 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / chandrashekar g

Actually there will be 4 wires ie 3ph 4wire system
for 230v supply can be achieved by taking one phase and one
neutral from it.

Is This Answer Correct ?

31 Yes

0 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / p.s,suresh

ph-ph voltage 415V.(3 Ph)

ph-Ne voltage 230V (1 Ph)

Is This Answer Correct ?

28 Yes

0 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / jitender kotwal

Is This Answer Correct ?

15 Yes

2 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / anand mishra

We can use 1ph-1neu for Covertion of 415v to 230v

Is This Answer Correct ?

8 Yes

1 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / kaushal

From distrubation transformer we get three phases and one
netural (due to Star connection) these four wire(three
phases and one netural)are layed over head on LT poles and
for house only one phase along with netural is used and no
convertor is used as phase to netural voltage is 230volt

between R -y- b phase voltages are 415 - 415-415 called
as line value where as between phase and neutral it will
be 415/1.732 = 239 approximately 230v called as phase value

Is This Answer Correct ?

4 Yes

0 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / a.y.naidu

actually transformer has two windings i.e primary and
secondary.primary is delta connected.secondary is star
connected.in delta 3 wires(3 ph) in star 4 wires(3 ph and
neutral).out come is

phase -phase--- 415V
phase -neutral--230V

Is This Answer Correct ?

4 Yes

0 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / shahzad

line voltage=the voltage between two phases=415v
phase to neutral voltage=line voltage/1.732=415/1.732=239.6v

Is This Answer Correct ?

4 Yes

0 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / soutrick chakraborty

Actually there will be 4 wires, 3ph 4wire system
for 230v supply can be achieved by taking one phase and one
neutral from it by lt pole but the four wire is come from lt
side, and the distribution transformer is delta star connection.

Is This Answer Correct ?

3 Yes

1 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / kranthi kumar k

ph-ph voltage 415v and ph-neutral voltage is 230v.only phase
wires runs in HT side.The nuetral wire is taken from the
step down transformer secondary side.So we can supply 230v
to houses by means of phase and neutral wire

Is This Answer Correct ?

2 Yes

4 No

In an LT pole, the line voltage is 415V. How is it converted to 230V into the house via the servic..

Answer / a.bala

u can take a 230 v supply by using one Phase Segregation
Distribution board

Is This Answer Correct ?

4 Yes

9 No

Post New Answer

More Electrical Engineering Interview Questions

HOW TO CALLICULATE RESITENCE,REACTANCE AND IMPEDENCE VOLTGE OF TRANSFORMER 13.33 KVA 144/240 VOLTS 93/56 A WITH FORMULA

0 Answers ISRO,

Why used IGBT IN AC Drives

4 Answers

Why X'mer rating in kva only?

4 Answers

Dear all, is ther any body who can tell me about the setting of ACB(air circuit breaker ). what kind of it,s setting is and how to do it,s setting. also please tell me the setting of VCB(vaccume circuit breaker) . please tell me their setting,s. i will b very thank ful to all of u. Thank,s and Regard,s. Muhammed Ikram.

2 Answers

how can we select the type of wire.what factors we have to look on it , do we have some formula to calculate it. please guide me on it

0 Answers

WHAT IS THE MEANING OF BALANCED / UNBALANCED IN STABILIZER TYPES.

0 Answers

which MPU register provides the address from which the next instruction byte is to be fetch?

1 Answers

compressor compresses air means exactly what happens?

2 Answers

How to derive detailed design of Suitable bus Bar for 100A for 6.6KV?

0 Answers

how will calculate the winding ohmic value in 3phase motors in h.p wise? ex.10 h.p motor winding value ph to ph ? 5 h.p motor any calculation please send me.

1 Answers Hyundai,

How good are you in resolving the commercial issues to Employer's advantage?

0 Answers

What is the numerical quantity of sqcm?

0 Answers

For more Electrical Engineering Interview Questions Click Here