which Machine u will prefer to use at place where Flammable gases are coming ou

Categories >> Engineering >> Electrical Engineering
Suggest New Category

which Machine u will prefer to use at place where Flammable
gases are coming out & why ??

Question Posted / crmeena

6 Answers
10127 Views
NTPC, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

which Machine u will prefer to use at place where Flammable gases are coming out & why ??..

Answer / prabhu

dc machines is not prefer to use at place where flamming
gases are coming out because it requires brushes and
commutator arrangements. it causes sparking during the
operations.
so we can go for Induction motors,preferable squrrle cage
induction motor are used. there are two types of IM.there
are i]slip ring IM ii]squrrle cage IM.
in the first one slip ring IM, it also not preferable
beacuse of slip ring arrangements. it also cause sparking.
second one squrrle cage is completely safe there is no
slipring arrangements.

Is This Answer Correct ?

45 Yes

0 No

which Machine u will prefer to use at place where Flammable gases are coming out & why ??..

Answer / vsr

yah the above said is right. go for squirrel cage induction
motor. but choose FLP type.

Is This Answer Correct ?

5 Yes

1 No

which Machine u will prefer to use at place where Flammable gases are coming out & why ??..

Answer / dpm

Flameproof type 3 phase squirrel cage induction motor ,
because it is widely used in gas industries due to its
rhobustness.

Is This Answer Correct ?

2 Yes

0 No

which Machine u will prefer to use at place where Flammable gases are coming out & why ??..

Answer / nik

Squirrel cage IM is the preferred choice, but if only a dc
supply is available then BLDC can be used.

Is This Answer Correct ?

2 Yes

0 No

which Machine u will prefer to use at place where Flammable gases are coming out & why ??..

Answer / x man

Explosion proof,increased safety Machines can be used for
these knid of applicaiton.
the explosion proof prevents the spark or ignition
happening inside to spread out
the increased safety protects the machince from the
environmental problems

Is This Answer Correct ?

1 Yes

0 No

which Machine u will prefer to use at place where Flammable gases are coming out & why ??..

Answer / perlsdelsur

Firth of all you may have to do a proper harzadous clacification area to determine if the place where you are going to install your motor is DIV 1, 2 or other (done by chemical certificated enginner)then after you must to select the suitable motor for that area operation, motor for harzadous manufacturers can give the information you need but you have to carefully to choice the correct motor because this involve to great riisk to choise a rong motor

Bye

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

WHAT IS THE THUMB RULE FOR DECIDING THE CURRENT RATING OF COPPER WIRES SAY 2.5/4/6/10 MM SQUARE SIZES??

14 Answers Dubai Group, Saudi Delta Groups, Savitha Electricals,

what bridge circuit is used in Tandelta circuit

1 Answers

what is physical distance of isolator to VCB in 33/11kv sub stations

0 Answers Enercon,

if AVR fails in D.G set, what will be the effect?

7 Answers

why output is out of phase in case of common emitter?

0 Answers

when it is possible kvrah lead & fundamental kwh be equal in electonic trivector meters (3 ph)

0 Answers

what is the diffrence between current transformer and voltage trasformer

3 Answers

difference between ac series and parallel circuit

0 Answers

how we have to calculate the short circuit current for 33/11kv 2mva, 7.5% Z, Transformer primary side breaker and secondary side breaker short circuit current for both sides?.

5 Answers

what is ratio of copper wire size and current ?

0 Answers

When a square wave is applied to primary of a transformer then what will be output wave form of secondary ?

2 Answers Sail, TCS,

Why consider motor rpm to select capacitor for motor

1 Answers KSEB,

For more Electrical Engineering Interview Questions Click Here