Answer / amol potdar

DC

Answer / jignesh kadia

dc is more dangerous than ac...

in ac the current passes through zero in 100 times per sec.
when frequency is 50hz...

in dc they have no freq. so current not passes through zero..

when u get a socked ac leave u to 100 times in sec.but dc
does not leave u.

Answer / smit sharma

Both are dangeruos but DC is more dagerous than AC because
AC is alternating current & flow of sine wave & once a cyle
is zero and maximum for take reference line, but DC is
direct current & not fraction of time period for reference
line and DC flow of state line,so DC is dangerous.

Answer / john zachariah

dc is more powerful because it doesnt leave you

but grabs you...whereas ac current leaves you..

the equation says that AC=1.414*dc...but its all about the
amount or energy produced..but if you ask me which is
dangerous its surely.....DC.

Answer / harshit

when it comes to dangerous, A.C comes first.

BCOZ in cycles comes to zero for a very short duration and at high voltages time is not enough to put your body out of it.

at same voltage level a.c is most dangerous.

Answer / lamzamang

dc is more dangerous than ac bcoz in ac the voltage nd
current increases maximum nd decreases to zero it will be
varying but in dc does not varies its constant voltage nd
in an there is a chance for the current to leave abody due
to its alternating nature

Answer / jigyesh sharma

DC IS MOST DANGEROUS BCOZ OF ITS CONSTAN MAGNITUDE< AS AC
MAGNITUDE BECOMES ZERO ALSO. BUT IN DC IT NEVER HAPPENS.
SO DC ABOVE 50v is dangerous

Answer / bigdog calhoun

It depends on your "amps" (amperage output) An automobiles
DC ignition coil produces around 10,000 volts, yet it is
less dangerous than 110v AC that comes out of a typical US
wall socket. Why, because the amperage produced by the coil
is much lower.

Answer / t k singh

dc

Answer / popoy

DC will make your muscles contract and you can't let go. AC
does not cause a paralysis at the lower voltages that DC can.

We have one 500KVA transformer. We have tested REF relay and commissioned. After one and half year, due to some ground fault in one of the DB circuit Transformer tripped by REF relay. What will be cause and remedy. Please advise?

1 Answers  

What are merits & De-merits of State-Space Method? What is series programming, parallel programming, general programming & direct programming ? And, difference between these programmings Techniques ?

0 Answers  

What is the difference between 2 wires RTD's and 3 wires RTD's.Kindly explain the wiring diagram.

1 Answers   QAFCO,

which type of material is used to transformer laminated core?

6 Answers  

from which formula we select a capacitor rating?

0 Answers   CLG,

different b/w counter poise and ground wire

1 Answers   L&T, TCS,

A 3-PHASE TRANSFORMER IS USED TO STEP-DOWN THE VOLTAGE OF A 3-PHASE, 11KV FEEDER LINE. PER-PHASE TURNS RATIO IS 12.FOR A PRIMARY LINE CURRENT OF 20A, CALCULATE THE SECOUNDRY LINE VOLTAGE, LINE CURRENT AND OUTPUT KVA FOR FOLLOWING.A)STAR- DELTA.B)DELTA-DELTA.

0 Answers   Ispat, Red Bull,

how to convert the KVAR to microfarad??????????????????

2 Answers  

What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding?

2 Answers  

How a synchronous generator practically work? what is the function of avr(automatic voltage regulator)in synchronous generator?how the connection of avr to the generator made practically?please give me the answer.

6 Answers   Accenture, Heineken,

What is the feedback in the control system?

0 Answers  

how to find 5 kilo meter long under ground 33 kv cable fault location if IR VALUE shows 0.05 M ohm @5000 volt.and cable fault locator shows some time fault distance 3 kilo meter ,3.7 kilo meter and some time 1 kilo meter? now how to find the fault location that where is leakage. note--it is tested with 5000 kv megger and insulation resistance is 0.05 M ohm. and some time 0.03 M ohm comes.

0 Answers   OPS,