Answer / infodoss

Chock is used to increase the starting voltage. Chock
input is phase and output also phase.

Answer / nb subrahmanyam

tube has four pins ,connect the starter in series of upper
pins or lower pins. now give the supply to the tube light
light through choke ( choke is in seris with supply).

The function choke is supply the high voltage at the
starting of the tube light.

Answer / prasanna d nerkar

The chock is a current limiting device placed in series oo
lamp,

Answer / engr. arbab waheed ahmad

there are two types of tube lights
1) with starter
2) without starter

1)for "with starter" the connection diagram is connect the
upper two pins of tube with two pins of starter and the
from lower two pins one is connected to the neutral wire
and the other is connected to the phase wire through choke.

function of choke is that when current changes due to
starter it produces a high voltage in 1000v range to ionize
the gas inside the tube according to the eq.
V=Ldi/dt

Answer / somnath@ sterlite

choke is used to provide a starting voltage of about1000v ,
required for the ionization of gas inside the tube.

Answer / learn basic electronics

Tube light has 4 pins ..
Upper two pin connect with starter ..
Then two pin is remaining .
One pin make series connection with phase and next one pin of tube it's neutral.

Answer / learn basic electronics

Tube light have simply 4 pins .
Upper 2 pins connect with starter .
And down 1 pin make series connection with choke .
and next one is neutral .

Thanks here many electronics and electrical question answer
Mini little electronics project
You can visit
http://learnelectronicshelp.blogspot.com

Answer / joe90

Chock is something you eat and tastes really great.
Chock also stops aeroplanes from rolling away...

Radio Carbon dating is used in a) find diseases b) find the age of relics c) find the carbon content in the atmosphere d) none of these

2 Answers  

CAN ANY ONE EXPLAIN THE KNEE VOLTAGE OF THE CT?

3 Answers  

hi all, can any one tell me a website or document on basic interview questions on plc for a fresh diploma candidate?

1 Answers  

There are two nos of 33Kv/11Kv 5MVA transformers conecting through HT cable from substation having metering at substation itself.One transformer used at a time another remains stand by.Further 11 nos of 11Kv/440V transformers are attached on it and each transformer is having its own Power factor correction panel.Now one 33/11Kv transformer at no load condition/Stand by condition is having power factor in leading side upto 0.21 and while when another tranformer at same situation have power factor in lagging 0.42. Now one thing is clear that transformer one is having 1.5 Km long 33kv cable due to that PF goes in leading side and another is having only 250 mtr length remains him lagging. Now i want to know that how i can maintain the Power factor at no load/ stand by position though both are behaving in seperate manner.

1 Answers  

what is thyristor, how is it works

1 Answers   Sony,

what is meant by Ac & DC drives where its useful ? how its functioning ?

3 Answers  

Can i use to 3 phase 4 wire energy meter inplace of 3 phase 3 wire energy meter ?

4 Answers  

How to determine stage of Automatic Power factor controlling Relay(Apfcr)?

0 Answers   ABC,

how df/dt relay operates & how it works?

1 Answers  

in 11kv generators the neutral point is connected to earth via earth coil while in the 33 / 11 kv transformer the neutral point is connected to earth via earth resistor why? 

1 Answers  

What is the difference between Droop vs Isoch Control?

0 Answers  

Why in earthing, the earthing plate is put in vertical position? and further what is soft coke that is used in earthing?

3 Answers   Wipro,