what are the differences between MCB and MCCB ?
Answers were Sorted based on User's Feedback
Answer / harnath yadav
mcb is not avealeble set point
mccb is set point
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / mohan cp
MCB is not having the adjustment of protections like Over
Load, Short circuit, Earth fault and Instantaneous current,
but MCCB is having.
Is This Answer Correct ? | 22 Yes | 23 No |
Answer / suhel
mcb is an younger brother of mccb which work with low load
compare with mccb.mccb can use like switch but mcb can not.
Is This Answer Correct ? | 1 Yes | 2 No |
MCB(miniature circuit breaker) is low current rating only
MCCB(molded case circuit breaker) high current rating only
applicable.
Is This Answer Correct ? | 0 Yes | 1 No |
Answer / adeeth
mcb - basically used for domestic and Industrial
application very near to load end and rating not exceeding
100A and have a short circuit rating upto 18 KA.It uses
thermal trippin mechanism for protecting the load.
on the other end MCCB basically used in industrial
Application is more sensitive than MCB.ITs available from
10A to 2000A and Short circuit ratio from 10 KA to 200KA.IT
have both thermal and magnetic tripping function and
basically more sensitive than MCB.
Is This Answer Correct ? | 3 Yes | 6 No |
Answer / p.s.negi
MCB is the miniature circuit breaker and its use to single
phase its tripped heavy current by short circuit or any
reason. MCCB is the moulded case circuit breaker and used
to three phase its tripped on heavy current flow single
phase or two phase and include three phasein moulded
case.both are safty protection.
Is This Answer Correct ? | 6 Yes | 20 No |
Answer / p. naik
MCB is acircuit-breaker which can provide protection only
in the cases of shor-circuit.They can only be operated
manually. MCCB's have provisions for both under/over
voltages, it has provisions for motr mechonism to be fitted
on it, which allows us to operate them electrically. MCCB's
have chnge over(NO & NC)contacts for both SD(faults) and SDE
(electrical faults) which can be utillised for providing
fault indication lamps. MCCB's have higher ratings than
MCB's. MCB's of diffrent types are B-curve(lighting
loads),C-curve(motors),D-curve(capacitive).Both operate in
almost a simillar manner having a fixed & moving contact,
but MCCB's been with more "ACCESSORIES".
Is This Answer Correct ? | 8 Yes | 25 No |
Answer / kurinji
MCB is used where ever there is an balanced current flow in
three phase, it will maloperate in unbalanced load condition
But MCCB is used in place of high rating current and also
in place where there is unbalances in current it will
operate correctly in this condition
Is This Answer Correct ? | 13 Yes | 83 No |
Answer / blake australia
From what I recall:
-MCB is a main circuit breaker, which can be any type of
circuit breaker
-MCCB is a Metal Clad Circuit Breaker, which is generally
rackable from its slot and typically used for breaking much
larger loads.
Is This Answer Correct ? | 29 Yes | 221 No |
what is mean by single phasing used for electrification in rural area of maharashtra ?
In secondary transmission i.e., in distribution side, supply for homes are connected through different phases in order to balance the 3 phase load. But in practical we saw nearby house doesn't have power due to single phasing. But other two phases give supply. How it's possible? it doesn't make "single phasing"?
What are the minimum acceptable insulation resistances of insulation of underground cable suitable for 0.440kV,11kV, 33kV and 66kV?
In a three phase transformer(delta/star connected)when i touch one end of the bulb in any one phase and other end to earth..will the bulb glow or not..if not why?..i'm touching the bulb in star connected side...
before transformer oil dielectric strenght tests are taken the oil should be allowed to settle to remove option 1 air bubbles 2 gasses 3 contamination 4 water
how to find the resistance and gap volatage of the diode??
working principle a.v.r. ?
On what principle reluctance motors work?
Name two types of electrical analogous for mechanical system.
Transmission through a short line depends on
750kva 11/415kv transformer having percentage impedence is5.64%. 11KV HV whose current 39.37A and 415V LV whose current 1043.43A.resistance is 2.5ohm. find no load loss and full load loss?
why open circuit test is conducted on hv side and short circuit test is conducted on lv side of a transformer ?what is the reason for it ?