Lists Different types of Tappings.

Answers were Sorted based on User's Feedback



Lists Different types of Tappings...

Answer / sagar.tinkhede

Flange Tapping
Corner Tapping
Radius Tapping
Vena Contracta Tapping
Pipe Tap
Venturi Vena Contacta Tapping
D - D/2 Tapping

Is This Answer Correct ?    26 Yes 0 No

Lists Different types of Tappings...

Answer / banibrata mukherjee

1.Pipe tapping:2.5D-8D
2.corner/flange:1-1 inch.
3.Radius:D-D/2.

Is This Answer Correct ?    8 Yes 2 No

Lists Different types of Tappings...

Answer / k.k.rameshkumar

1.Corner taps
2.Flange taps
3. D and D/2 taps

Is This Answer Correct ?    4 Yes 0 No

Lists Different types of Tappings...

Answer / janes

Flange Tapping
Corner Tapping
Radius Tapping = Pipe Taps
Vena Contracta Tapping
D - D/2 Tapping

Is This Answer Correct ?    2 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

installation process of orifice,a question asked for confusion creation in interview by BARC 1.if orifice is tightly fitted with pipe ,it will act like venturi 2.if orifice is left hanging in between liquid it will not create the pressure difference exactly,

0 Answers   BARC,


What is the difference between Error and Offset.

1 Answers  


Speedtronic system .

0 Answers   CCIE,


in any transimitter (flow/level) there are three terminals for supply& test (+,-,+)in two wire,24VDC given to Tx.,but how 4-20 ma signal travels thru same wire (as it is for 24VDC input supply)?

1 Answers   Jindal, UltraTech,


what is the deluge ? How can its working?

2 Answers   KOC,






Is there a particular problem if two proposals from the same observatory (originating with different partners) are submitted?

1 Answers  


Are Coils of Electromagnetic flowmeter in direct contact with fluid material

4 Answers   TATA,


what is formula for calculating flow if i have pressure and pipe diameter?

1 Answers  


How to calibrate RC Feeder system in thermal power station?,If any instrument available to calibrate it,ple inform me. make:stock,

0 Answers   TATA,


How to get Cv of control valve having following parameter ,i.e inlet pressure 4.5kg/cm2 outlet pressure 1 kg/cm2 specific gravity 0.808

3 Answers  


Isometric drawings are generated during _________________ phase of a project

0 Answers  


How the flow can be measured by using DP Transmitter?

3 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)