what happens when ac supply is given to D.C motor.

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / guest

17 Answers
31843 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what happens when ac supply is given to D.C motor...

Answer / mallikarjun n

nothing doing...if we give dc supply,o/p will be 24vplts..
if ac,o/p will be 230 volts.if we give ac,motior will run
at const speed.if we give dc,it wil start at 50rpm and
gradully increase 2 160rpm,if it crosses rated rpm winding
will burn will more spark induction takes place..
so dont give ac supply 2 dc motor.be careful

Is This Answer Correct ?

2 Yes

1 No

what happens when ac supply is given to D.C motor...

Answer / maulik

motor willl run but it will run with reduce speed and also there is a spark in the motor

Is This Answer Correct ?

1 Yes

0 No

what happens when ac supply is given to D.C motor...

Answer / nagarjuna

the motor wil not run

Is This Answer Correct ?

8 Yes

8 No

what happens when ac supply is given to D.C motor...

Answer / karthik.n

Because of the presence of low resistance in DC motors. The
motor will not with stand the AC current voltage so the
motor burns after working for some desired period.

Is This Answer Correct ?

1 Yes

3 No

what happens when ac supply is given to D.C motor...

Answer / mahender

if dc motor is shunt type, then it will rotate.But, if it is
separately excited dc motor then, the motor will not rotate
due to quick change in its direction per every cycle.

Is This Answer Correct ?

0 Yes

4 No

what happens when ac supply is given to D.C motor...

Answer / aniruddh

AC apply to DCmotor frequency dependent losses increse
(eddycurrent&core)losses
motor gives less output

Is This Answer Correct ?

4 Yes

18 No

what happens when ac supply is given to D.C motor...

Answer / sam khanji

The Motor will run only on the positive side of the Ac
wave .so it will run and stop then run again and stop again.
but if the volume of the AC is high, then the winding will
be burned due to the high frequency exposed to

Is This Answer Correct ?

5 Yes

20 No

Post New Answer

More Electrical Engineering Interview Questions

what is the principle of switchgear and its function

1 Answers

What is the dc grounding system and what is diff between AC/DC grounding system?

0 Answers

Whats the minimum value for I.R. that can be allowed for HT & LT alternators for operation?

1 Answers

why a motor overheated stops to rotate ?????

1 Answers

What is ideal IR values for ground and neutral.

0 Answers Hindustan Power Projects,

draw 3 phase rectifier diagram

0 Answers Equate,

what is brushless generator.How does work it..??

3 Answers NTPC,

1)How much current can a 3-1/2 core 100 mm wire carry? 2)What are the special cables required for explosion proof wiring? 3)In case you do not have coal and salt for earthing, how can you achieve good temporary earthing? 4)One horse power single phase motor is more likely to get hot than a one horse power 3 phase motor. Is it true or false, if true why? 5)What are the different types of soft starters for large motors?please explain?

0 Answers TATA,

What is the difference between Droop vs Isoch Control?

0 Answers

WHAT IS FAULT CAPACITY OF HT MOTOR TERMINAL BLOCK? ANY BODY HAVE ANSWER PLZ....POST IT.

0 Answers Birla,

Dear Sir / Madam, Actually we requied 64 A MCB, But i have 32 A MCB = 2 No's this two i have to make series connection and we usw any place? isit possible or not......

4 Answers Hindustan Unilever Limited,

what is the bus bar size of 2700 amp ACB breaker ? and what is the cable size ?pls detailed answer ?

3 Answers

For more Electrical Engineering Interview Questions Click Here