what three specific job positions do u target from the
company.




Answers were Sorted based on User's Feedback



Answer / ahmed

Manager , Senior Manager And Area Manager

Is This Answer Correct ?    31 Yes 11 No

Answer / mohammad kamruzzaman

I) Project Engineer.
II) Civil Engineer
III) Design Engineer

Is This Answer Correct ?    6 Yes 2 No

Post New Answer




More Chemical Engineering Interview Questions

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.6 : In infrared spectrum, one of the factors affecting peak location is the mass of the atoms. The stretching frequency of a bond connected to a lighter atom will be greater than the same bond connected to a heavier atom. (a) For halogens like florine (F), chlorine (Cl), bromine (Br), iodine (I) and astatine (At), what is their IUPAC group number? Hint : The proton numbers for F, Cl, Br, I and At are 9, 17, 35, 53 and 85 respectively. (b) For the compounds of H-F, H-Cl, H-Br, H-I and H-At, which one has the lowest stretching frequency and which one has the highest stretching frequency? State the reasons.

1 Answers  


In Galvonised iron and stainsteel pipes, in which pipe friction losses will more and why ?

0 Answers  


ELECTRICAL TECHNOLOGY - EXAMPLE 16.1 : According to Shockley equation, the I - V characteristic of a diode is approximated by I = IS [ exp (nVD / VT) - 1 ]. For silicon, let the reverse bias saturation current IS as 0.000000000001. If n is ideality factor with value of 1.5, VT as thermal voltage drop of 0.026 V at room temperature, what is the value of current I that passes through the silicon diode in the heater of evaporator when the forward voltage drop VD = 0.026 V? Please take note that exp is the exponential function with e(1) = 2.718, e(2) = 7.389.

1 Answers  


NATURAL GAS ENGINEERING - QUESTION 26.1 : (a) In natural gas pipe sizing, the length of the pipe from the gas source metre to the farthest appliances is 60 feet. The maximum capacities for typical metallic pipes of 60 feet in length are : 66 cubic feet per hour for pipe size of 0.5 inches; 138 cubic feet per hour for pipe size of 0.75 inches; 260 cubic feet per hour for pipe size of 1 inch. By using the longest run method : (i) Find the best pipe size needed for the capacity of 75 cubic feet per hour. (ii) Estimate the suitable range of capacities for the pipe size of 1 inch. (b) The maximum capacities for typical metallic pipes of 50 feet in length are : 73 cubic feet per hour for pipe size of 0.5 inches; 151 cubic feet per hour for pipe size of 0.75 inches; 285 cubic feet per hour for pipe size of 1 inch. By using the branch method find the best pipe size needed for the capacity of 75 cubic feet per hour when the length of the pipe from the gas source metre to the appliance is 52 feet.

2 Answers  


ENGINEERING ECONOMY - EXAMPLE 7.3 : There are 2 alternatives of investment. Choice 1 : A trader offers you an investment opportunity where your investment of A$15000 presently will be A$18000 after 4 years. Choice 2 : A bank offers you 5 % annual return for your initial investment of A$15000. Question a : What is the equivalent bank payment after 4 years? Question b : By using the concept of equivalence in engineering economy, which is the better choice, between 1 and 2, that will be more profitable after 4 years?

1 Answers  






what is isochronus and droop speed?

0 Answers  


How many pounds (lb) are available in 1 kilogram (kg), 1 metre (m) has how many feet (ft) and 1 meter (m) has how many inches (in)?

1 Answers  


what is the hearth and arch pressure in furnace?

0 Answers   TATA, Essar,


What is cathodic protection, how it works in Turbine condensers ?

0 Answers   HPCL, HQL,


ENGINEERING MATHEMATICS - EXAMPLE 8.1 : A local utility burns coal having the following composition on a dry basis : Carbon (C) 83.05 %, hydrogen (H) 4.45 %, oxygen (O) 3.36 %, nitrogen (N) 1.08 %, sulfur (S) 0.7 % and ash 7.36 %. Calculate the ash free composition of the coal with reference to C, H, O, N and S.

1 Answers  


Question 89 - A hemocytometer is a device that is used for counting cells. In an engineering experiment, 100 microlitres of cell suspension is diluted with 50 microlitres of Trypan blue dye. Only death cells appear blue in color when stained with the dye. There are 57 cells detected in a hemocytometer, where 5.3 % of them appear blue when the chamber of the meter is placed under a microscope. Each square of a chamber can contain 0.0001 mL of liquid. (a) Calculate the number of viable cells. (b) The cells ocupied 5 squares. Calculate the average number of viable cells / square. (c) Calculate the dilution factor of the cell suspension by using the formula : Dilution = final volume / initial volume. (d) Calculate the concentration of viable cells / mL by using the formula : Concentration = (Average number of viable cells / square) x dilution x (square / volume).

1 Answers  


what is fund flow definition

1 Answers   Amara Raja,






Categories
  • Civil Engineering Interview Questions Civil Engineering (4619)
  • Mechanical Engineering Interview Questions Mechanical Engineering (3695)
  • Electrical Engineering Interview Questions Electrical Engineering (15732)
  • Electronics Communications Interview Questions Electronics Communications (2633)
  • Chemical Engineering Interview Questions Chemical Engineering (761)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (79)
  • Bio Engineering Interview Questions Bio Engineering (30)
  • Metallurgy Interview Questions Metallurgy (95)
  • Industrial Engineering Interview Questions Industrial Engineering (199)
  • Instrumentation Interview Questions Instrumentation (2866)
  • Automobile Engineering Interview Questions Automobile Engineering (171)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (41)
  • Marine Engineering Interview Questions Marine Engineering (60)
  • Power Plant Engineering Interview Questions Power Plant Engineering (168)
  • Engineering AllOther Interview Questions Engineering AllOther (1331)