Answer / s.k.pavar

Generating voltage of power station is generally considered
as 11 kv to 15 kv

Answer / r.ravi

6.6kv 11kv or 15.5kv or 33kv generaly used in power plant

Answer / v.swathanthra babu

11KV MAY BE OPTIMUM CONSIDERING COIL SIZE AND INSULATION COST. i.e., for particular range of capacity the generating voltage is less than 11KV means current level high in turns coil size will increase, generator size and cost also goes up. In vise versa generation voltage more than 11KV winding insulation cost may go up. Generator Capacity ranges from 10 to 110 MW the machines sized for 11KV which may be optimum and economical on considering efficiency of machine, cost and transportability limits.

Answer / prabhu_la@yahoo.com

Generally maximam generating station are produced 11Kv voltage
and depend upon Powerplan capacity its distributed to substation after will desided use transformer stepup or step down

Answer / perveenkumar

In India it start from 3.3kv then 6.3kv, 6.6kv, 11kv13.2kv,
13.8kv, 15kv till 25 kv.

Answer / shaberabegam

generating stations generating voltage is11kv


in india

Answer / rahul sharma

Depends on the load requirement of perticular location and
is generally 11KV,22KV,33KV,66KV,110KV,220KV etc

Answer / gautam himmatramka

10.5 KV....it is at Hindalco supporting power plant

Answer / pavan

depended on capacity of power plant

Answer / aravinda

25 kv to 40 kv

how many earthing should need for UPS, where its connected

7 Answers   HCL,

1)What will you do if main incomer VCB fail in your site ?

7 Answers   Honeywell,

Sparking occur when a load is switched off because the circuit has high – a.) Inductance b.) Capacitance c.) Resistance d.) None

3 Answers   Ecil,

Why more sound is produced in mixer than grinder

2 Answers   Vedant,

I have a question, I visit 01 site and face a problem, there is 2.5 ton Air Con working, when air con compressor is running at that time rectifier voltages are increasing upto 290-295 v and rectifier is giving main high alarm (rectifier is APC single phase, before starting compressor rectifier voltages was 230v. when air con is going off rectifier voltages are decreasing smoothly at its actual voltages 230v. Load on Genset phases is this: Red-13.5 amp AC (Air Con load), Yellow-1.7 amp AC (BTS lights etc.) and Blew-4 amp AC (telecom system load), Genset phase to phase and neutral to phase voltages are also ok. These are 10 sites having same system and same rectifier APC brand at every site 02 genset are working but the problem is same at all these 10 sites. What will be the reason behind???

1 Answers  

i want design of D.C.MOTOR 1HP 960RPM AND 2HP 960RPM ITS URRGENT

0 Answers  

we can run 2phase as 3phase .what will be the differnce with respect to phase angle, power, current between the two modes

0 Answers  

what is the different beetween kva and kwh?

4 Answers  

Why field rheostat is kept in minimum position?

0 Answers  

WHY DOES NEUTRAL DO NOT CARRY EVEN THOUGH IT CARRIES RETURN CURRENT?

4 Answers  

Dear sir,how should i set the relay in star delta starter..say ex i am having 4ohp motor,,wht should be the relay setting...?

4 Answers  

please can i know about total harmonic distortion and how i can calculate it and if anyone can help me to find any program to help me to calculate THD?? please need it

1 Answers