PETROLEUM ENGINEERING - QUESTION 25.2 : (a) The American Petroleum Institute gravity, or API gravity, is a measure of how heavy or light a petroleum liquid is compared to water. Let SG = specific gravity of petroleum liquid, and V = barrels of crude oil per metric ton. Given the formula for API gravity = 141.5 / SG - 131.5 and V = (API gravity + 131.5) / (141.5 x 0.159), find the relationship of SG as a function of V. (b) An oil barrel is about 159 litres. If a cylinder with diameter d = 50 cm and height h = 50 cm is used to contain the oil, find the volume V of the cylinder in the unit of oil barrel by using the formula V = 3.142 x d x h x d / 4. (c) First reference : 1 cubic metre = 6.2898 oil barrels. Second reference : 1 cubic metre = 6.37 oil barrels. What are the 2 factors that cause the difference in such reference data?

1 Answers  

---

What is a black body?

0 Answers  

---

What is difference between overall heat transfer coefficient & individual heat transfer coefficient?

0 Answers  

---

How can one determine the particle size distribution for a given bulk solid?

0 Answers  

---

What are the some common causes of control valve noise?

0 Answers  

---

---

What is the most common carrier gas used in pneumatic conveying?

0 Answers  

---

FOOD ENGINEERING - QUESTION 23.2 : (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80 °C to 71 °C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71 °C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24 °C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80 °C, and the air is cooled to 71 °C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To) / (Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.

1 Answers  

---

What fluid first to be lined up in a heat exchanger whether hot or liquid?why?

2 Answers   TCL,

---

Question 64 – According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

what is water at its saturation temperature ??????????

2 Answers   Essar,

---

Water flows through a pipe with circular cross sectional area at the rate of V / t = 80 L / s where V is the volume and t is time. Let Av = 80 L / s where A is cross sectional area and v is velocity of fluid. For point 1, the radius of the pipe is 16 cm. For point 2, the radius of the pipe is 8 cm. Find (a) the velocity at point 1; (b) the velocity at point 2; (c) the pressure at point 2 by using Bernoulli’s equation where P Rgy 0.5 RV = constant. P is the pressure, R = density of fluid, V = square of fluid’s velocity, g = gravitational constant of 9.81 N / kg and y = 2 m = difference of height at 2 points. The pressure of point 1 is 180 kPa.

1 Answers  

---

The process conditions of the fuel gas are as follows: Temperature = 25 deg C Pressure = 4 bar g Calculate the line size for the fuel gas supply line to the superheater

0 Answers  

---