Interested to Buy Any Domain ? << Click Here >> for more details...
where we use one way slab and two way slab?
- 7 Answers
- 19198 Views
- SRM, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / hari
(Ly/Lx) ratio is grater then two the slabs are called one
way slabs. in most of the times these slabs are rectangular.
(Ly/Lx) ratio is less then two the slabs are called two way
slabs. in most of the times these slabs are square.
| Is This Answer Correct ? | 21 Yes | 2 No |
Answer / harmanpreet singh
two way slab used when L/B ratio is < then 2
where as one way slab is used when L/B ratio is > then 2
| Is This Answer Correct ? | 7 Yes | 0 No |
Answer / rajesh.d.v.s.p.
(Ly/Lx) ratio is grater then two the slabs are called one way slabs. in most of the times these slabs are rectangular.
(Ly/Lx) ratio is less then two the slabs are called one way slabs. in most of the times these slabs are square.
| Is This Answer Correct ? | 14 Yes | 10 No |
Answer / muhammad junaid
ONE WAY SLAB :
The reinforcement for bending moment will be onle one direction and other reiforcement will be disttribution steel.
TWO WAY SLAB:
The reinforcement for bending will be in two direction
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / akram
L/B value is = more than 2 then these slab is Called as one way slab. in this slab the main Reinforcement will be providing in one direction.
L/B value is = Less than 2 then these slab is Called as two way slab. in this slab the main Reinforcement will be providing in both directions.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / abdur rasheed
any slab which is supported on lesser than four sides will be called one way slab.But if the slab is supported on four sides then we have to consider the aspect ration (Lx/Ly).If the aspect ratio is more than 0.5 then it is one way otherwise two way slab.
one way examples are,
stair slabs
cantilever slabs
retaining walls etc
| Is This Answer Correct ? | 1 Yes | 2 No |
How to test the soil compaction test?
what is water cement ratio and how to calculate it after designing the concrete?
what is the percentage of silt in black cotton soil.?
why you are selecting the civil engineering
4 Answers gdcl, Sobha Developers,
how the lap length is calculated in reinforcement of 110mm dia steel of Length 15.00 mtrs. & grade of concrete is M20
What is HEAVIER? A kilo of SAND OR A kilo of GRAVEL?
how much cement and sand is used for plastering 1646 sq feet,for 12mm thickness and ratio 1:4
what a pigment?
material calculations for I st coatplastering 16mm CM (1:5),second coat CM(1;3)4mm thick,pcc(1:4:8),RCC M20,lime stone masonry CM(1:6)
A doubly reinforced concrete beam is 25 cm wide and 50cm deep to the centre of tension reinforcement. The centre of compression is steel is 5cm from the compression edge. The areas of the compression and the tension steel are 10.16cm2 and 12.56 cm2 if m=18 and the bending moment at the section is 7,000,000 N-cm. Calculate the stress in concrete and steel.
why green colour formation on the surface of concrete and plastered surface takes place after curing?
What is the stripping time of shuttering for PPC concrete
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
