wat is fe full form in fe4l5?

Categories >> Engineering >> Civil Engineering
Suggest New Category

Question Posted / guest

7 Answers
24023 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

wat is fe full form in fe4l5? ..

Answer / venkat

fe stands for ferrous.415 stands for tensile strength
subjected to elongation

Is This Answer Correct ?

26 Yes

3 No

wat is fe full form in fe4l5? ..

Answer / arjun kumar

fe stands for ferrous and 415 is the characteristic
strength of steel in N/mm2 or yield stress of steel

Is This Answer Correct ?

21 Yes

0 No

wat is fe full form in fe4l5? ..

Answer / ratheesh

Fe = Ferrous iron
415 = characteristic srength N/mm2

Is This Answer Correct ?

14 Yes

1 No

wat is fe full form in fe4l5? ..

Answer / siba sankar sahu

Fe means Furious Iron
& 415 is Tensile strength of steel i.e 415 N/mm^2

Is This Answer Correct ?

4 Yes

1 No

wat is fe full form in fe4l5? ..

Answer / venkatakrishna

Fe -థStands గIron
and 415- stands
characteristic
strength units -N/
ఠmm2 నఅప

Is This Answer Correct ?

0 Yes

0 No

wat is fe full form in fe4l5? ..

Answer / d vishwanath s

Fe - ferrouse iron
415- chacteristics strenth of steel or yeild stress of steel

Is This Answer Correct ?

0 Yes

0 No

wat is fe full form in fe4l5? ..

Answer / bhosalepravin20

fe - symbol used for iron . &
415- yield strength in MPa.

Is This Answer Correct ?

3 Yes

4 No

Post New Answer

More Civil Engineering Interview Questions

How to calculate density(dry & bulk) of sand from Sp. ravity value of sand. eg. G=2.5

1 Answers

What is the cement and sand content in the mortar used to build 1 sqm of 190x190x390mm hollow and solid blockworks?

2 Answers

please differentiate duties and responsible for civil site engineer , Quantity suryevor ,Quality control engineer and Planning engineer

1 Answers

How much quantity of cement and sand required for the inlining of 610mm dia MS pipe 8.7mm thk.Inlining thickness is 10mm and CM ratio is 1:1.5.

0 Answers IVRCL,

1) write Short notes about Shellow & Deep well? 2) What is the full form of SPT & SMB? write short notes. 3) write short notes about efficiency of Riveted joint.

0 Answers Gammon, Rajiv Gandhi University of Knowledge Technologies RGUKT,

How much steel required in one cubic meter RCC Main girder

1 Answers Isolux Corsan,

How many feet are in 4 square yards?

0 Answers

A bill was raised by contractor which read as follows 1.) Excavation in normal soil upto 1.5m - 250 cum 2.) Excavation in normal soil 1.5m to 3m - 240 cum 3.) Excavation in soft rock - 350 cum 4.) Excavation in hard rock - 250 cum 5.) Filling with available soil - 825 cum 6.) Filling with bought out soil - 1100 cum How can I verify the above quantities, especially for item no. 5 & 6? What checks are necessary before releasing the bill ?

5 Answers

logical reasoning

0 Answers

What is rate for brick masonry work of 1.0 m3 in cm 1:6?

0 Answers

how to calculate the 45 degree bent up length. if we given that whether the total length of the slab reinforcement will increase or not. mantion it clearly please. this is for bar bending schedule purpose?

4 Answers Indian Army, L&T,

what is the size of shuttering?????

4 Answers SKV Builders and Development Pvt Ltd,

For more Civil Engineering Interview Questions Click Here