pl.may i place dry mix in casting of drain bed partialy filled
with water?if no pl explain.

Answers were Sorted based on User's Feedback



pl.may i place dry mix in casting of drain bed partialy filled with water?if no pl explain...

Answer / ram narendranath

Don't pour the concrete in partially filled drains because of there will be more water than the requirement for concrete in that case cement will may be drained out also. It is necessary to remove maximum possible water after wards fill the damp area with Coarse sand after wards you have to pour the concrete for Drain bed. Otherwise cement is to be add to water to maintain the cement quantity in concrete as per requirement.

Narendra

Is This Answer Correct ?    2 Yes 0 No

pl.may i place dry mix in casting of drain bed partialy filled with water?if no pl explain...

Answer / guest

the strength of concrete will be more when the w/c ratio will
be less but as per work-ability concern i have to provide
minimum amount of water .

Is This Answer Correct ?    2 Yes 1 No

pl.may i place dry mix in casting of drain bed partialy filled with water?if no pl explain...

Answer / artic

If you are not adding water cement will not react and you
will not get any strength. So you have to add water as low
as possible(0.3)

Is This Answer Correct ?    1 Yes 0 No

Post New Answer

More Civil Engineering Interview Questions

What is anchorage length

1 Answers   ABPL, SBDL,


TO RESISIT TORSION IN BEAMS WHAT KIND REINFORCEMENT IS PROVIDED?

2 Answers  


Pile height is 4.3m. 2nos. under reammer. bulb nose is 75mm and height is 400mm. pile dia is 375mm and overall dia 940mm.pls. help to calculate concrete in pile and bulbs separately. What is formula for bulb volume calculation ?

0 Answers  


how to design paver block

1 Answers   CCCL,


WHAT DLC DESIGN IN CONSTRUCTION

0 Answers  






In structural steel work what should be the wastage percentage considered to order the material( 200x200x5mm box section) in standard available sizes in India i.e. 6 mtrs?

3 Answers  


What is difference between engineering stress and true stress?

0 Answers  


what are the checks to be performed while fixing a door and a window frame..at site??

3 Answers  


2. In a container filled with each of the following materials, at a porosity of 40%, determine the upward gradient required to cause the quick condition (a) Lead shot with a G = 13.75; (b) Fibre beads with G = 2.15; (c) Sand with a G = 2.32

0 Answers  


which one is economical construction brick masonry or sold block masonry?

3 Answers  


What is tha cutting lenght off samosa ring in column 300*600.

2 Answers  


what is the quantity of cement sand and metal in a 1m^3 m15 standard concrete

2 Answers   CCE, NCC,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)