Answer / riyazkhann21

i apologize for the mistake in previous answer,vena
contracta is the (least)area where flow pressure is MINIMUM
and flow velocity is MAXIMUM

Answer / akash

When a fast flowing fluid in a pipeline encounters an obstruction, it bends its or skids over the encounter. Normally this encounter is known as an orifice. Here, the fluid flow diameter attains its minimum diameter just after the orifice/obstruction. This region is called vena contracta. The exact distance of vena contracta from the orifice depends on variety of factors out of which the velocity of flowing liquid, pipe dimension, orifice dimension (or beta ratio), viscosity are most crucial.

http://www.google.com.au/imgres?imgurl=http://circ.ahajournals.org/content/97/16/1597/F1.large.jpg&imgrefurl=http://circ.ahajournals.org/content/97/16/1597/F1.expansion.html&h=937&w=1800&tbnid=n0uZRwtoOq42yM:&docid=VSBT8zCOz274MM&ei=GxMeVp7LFYTgoAT01rLoDw&tbm=isch&ved=0CB4QMygCMAJqFQoTCN7EsLjGwcgCFQQwiAoddKsM_Q

Answer / riyazkhan r malek

vena contracta is the (least)area of the pipeline where flow
pressure is maximum and flow velocity is minimum.

what is Instrument Schedule, and what it is mainly used for?

0 Answers  

---

List three types Level Gauges with their working principles

1 Answers   ABB,

---

1.Give example of analog and digital signal 2. What is yhe advantage of 8086 than 8085

5 Answers   Bhel, College School Exams Tests, Profitec,

---

SIR MAY I KNOW IF RADAR TYPE LEVEL TRANSMITTER SHOWING IN THE FIELD 0 % LEVEL AND IN DCS SHOWING 100% THEN WHAT IS THE CAUSE I CLEAN THE CHAMBER & TAKEN ONLINE BUT ONLY ONCE ITS BECOME ZERO IN DCS BUT AGAIN 100% SHOWING IN DCS,THEN I REMOVE THE POWER SUPLLY AND CONNECT IT AGAIN .IS IT OK BUT STILL IN THE DCS ITS 100% AND ON THE DISPLAY ITS INITILAZIATION PLEASE HELP ME READRING THIS?

4 Answers  

---

What is the use of temperature compensation?

1 Answers  

---

If an Instrument has 550 ohm internal resistance and the cable used for that instrument is 0.5 ohm per meter resistance. If the voltage is 12volt.How much length cable can be used? Please tell me its Calculation formula.

5 Answers   MOL,

---

HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,, I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION .. ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY MANIFOLD..!!! BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 , SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT.. THANKS YOURSSSSSSS

1 Answers   Torrent Pharma,

---

what is difference between wheatstone bridge, pirani gauge and strain gauge ??? explain its principle and working

4 Answers  

---

what is the difference between attemperator and desuperheater ?

1 Answers  

---

I have completed B.E. Instrumentation & control in 2009. i have 3 year industrial job experience in chemical plant.now, I want to join M.E. in external. so, Plese say easiet way and good institute name.

1 Answers  

---

What is the differaence between PLC and DCS?

6 Answers  

---

How to calibrate DP transmitter by using HART communicator ?

1 Answers  

---